Schlage Lock

From MiOS
(Difference between revisions)
Jump to: navigation, search
(Scenes and Events)
 
(102 intermediate revisions by 9 users not shown)
Line 1: Line 1:
=Setup=
+
[[Category:User Instructions]]
 +
[[Category:Hardware]]
 +
= Secure Z-Wave Devices Explained  =
  
NOTE: If you purchased your Vera before December, 2008, in Vera's setup page go to Devices, Z-Wave options, and look at the 'Version'. If the version is 2.40 your dongle does not have the security class implemented.  Send a support request at micasaverde.com, support, with your serial number, name, address and email.  We will send you a replacement dongle.
+
Door locks are a special breed of Z-Wave devices which require an exchange of security keys with Vera during the 'Include' ("pairing") process.&nbsp; Accordingly, the normal 'Include' procedure - carrying Vera's black Z-Wave dongle to the device - will <u>not</u> work with Schlage locks.&nbsp; Instead, Schlage locks must be paired with Vera using a special procedure (see 'Adding/Pairing a Lock', below).  
  
NOTES:
+
In order for Vera to interoperate successfully with a Schlage lock or other secure Z-Wave device, the following conditions must all be met:<br><br>'''1)''' Vera's Z-Wave dongle must have a built-in security class:<br>'''Go to Setup -&gt; Devices -&gt; Z-Wave Options''', and look at the ''''Version''''.<br>If the&nbsp;<span style="color: rgb(255,0,0)">'''version is 2.40 '''</span>'''your dongle does <u>not</u> have the security class implemented.'''&nbsp; Request a replacement dongle by sending us a support request at the [http://www.micasaverde.com micasaverde.com] website (click 'Support'), including your serial number, name, address and email.<br>
1) You also need firmware version 1.0.500 or greater.  Go to advanced, download and confirm the version of your firmware.
+
2) The schlage lock works on the Zensys "Zensor Net Technology". This aids in prolonged battery life in battery powered Zwave devices. If the Schlage lock cannot be in direct communication to Vera and it's signal must me routed to vera. "the last node in the route must be capable of Zensor net "beam". The only Zwave device out on the market known at this time is the Homepro ZDP100 ver3.3( must be latest firmware ver 3.3)  or the Schalge branded unit part #RP200.
+
Try the lock without first close to Vera and then move to the location of the door. If it works you're good to go.  
+
  
You cannot add these types of secure devices the normal way of removing Vera's black Z-Wave dongle.  You must add them with the dongle attached, and the device must be within a few feet of Vera when you add it.  Do this either from the [[ZWave_Options]] page, or, if the door lock is already mounted, bring Vera near the door lock, plug Vera's power into a nearby outlet so Vera is within a few feet, and use the red/black buttons as explained in 'Adding/Removing ZWave devices' here: [[Buttons_Indicators#Adding.2FRemoving_Z-Wave_devices|Adding/Removing Z-Wave devices with the red/black buttons]]. This allows you to add the device without your web browser and without having to connect Vera's network cables.  Note that even if Vera's network cables are not connected, the wi-fi is still active.  So you can also connect to Vera over wi-fi, and visit http://192.168.81.1, to control and test the door lock without connecting Vera back up again to your home network.
+
'''2)''' Vera's firmware must be <span style="color: rgb(255,0,0)">'''version 1.0.602 or later'''</span>:<br>'''Go to Setup -&gt; Advanced -&gt; Download''' and confirm the version of your firmware.<br>
  
Adding a secure device like the Schlage lock takes longer than adding a normal, non-secure device because Vera needs to share encryption keys with the device.  When the Schlage lock is successfully paired and the secure network has been setup, the 'Schlage' button on the front of the lock will blink green. To make the Schlage lock pair, enter the 6 digit program code followed by 'schlage' 0.
+
'''3)''' The range for the Schlage lock is much less than for other devices because the antenna is inside a metal housing. The distance (in open air) between Vera and your lock should not exceed 30 feet (if you have two walls between them, the distance should be much lower). You can use a [http://www.newegg.com/Product/Product.aspx?Item=N82E16812191054 USB Cable extender] to place Vera's Z-Wave dongle closer to the lock. (If you change&nbsp;the dongle position, don't forget to do a [[Heal Network]] after.) Otherwise you will need to add other modules to act as Z-Wave relays, as explained in #4.
  
To control the lock, use the lock/unlock buttons.  Because the current Schlage locks are not motorized, the lock and unlock buttons do not actually move the deadbolt.  Rather they simply engage the latch, just like when you enter your PIN code. To allow remote access you can choose Vera's lock/unlock command when the person is in front of the door, and he will have a couple second to manually turn the latch. Or you can create a user code for him. Do this by entering a code number in the box on Vera's control page, and then the PIN number, and choosing 'Set'.  The code number is just a 'slot'.  It must be a number between 3 and 10. So you can assign 8 codes. The PIN codes remain active until you remove them. To remove a PIN code, enter the code number (3-10), leave the PIN blank, and click 'Set'.
+
'''4)''' Schlage locks work with Zensys' "Zensor Net Technology" which prolongs battery life for battery-powered Z-Wave devices. If the Schlage lock cannot be in direct communication to Vera and its signal must be routed through other Z-Wave devices, the <u>last</u> node in the route must be capable of "Zensor Net Beam" (ZNB). Many newer Z-Wave devices support Beaming, including:<br>
 +
'''I)'''any GE/Jasco lamp modules/switches with the following versions:<br>
 +
2.0a<br>
 +
3.0a<br>
 +
2.0b<br>
 +
3.0b<br>
 +
NOT 2, 2.0, 3, or 3.0<br>
 +
'''II)''' the Homepro ZDP100 lamp module (must be firmware version 3.3 or later). Also, after you've added lamp modules, you must do a [[Heal Network]] before they will effectively act as relays. [[Heal Network]] will also give you a report to confirm that Vera can talk to all your Z-Wave devices<br>
 +
'''III)''' and the Schlage RP200 light module. .<br><br>
  
NOTE: The lock is not ready to be used until you see the green cog meaning it's configured ok (see [[Device_Control_Status]]).  It can take Vera several minutes to configure the lock because a lot of encrypted data is being exchanged in the process. Whenever you rename the lock, change its room, or change configuration settings (other than assigning PIN codes), Vera will need to re-configure the lock again.
+
= Setting Up a Schlage Lock with Vera  =
  
'''Method 1'''
+
== Adding/Pairing a Lock  ==
The typical sequence to pair the Schlage lock is:
+
  
1.  Disconnect Vera and move Vera close to the Schlage lock. Power up Vera using the nearest outlet.
+
Adding ("pairing") a secure device like the Schlage lock takes longer than adding a normal, non-secure device because Vera needs to share encryption keys with a secure device.&nbsp; IMPORTANT: Leave Vera's black Z-Wave dongle inserted when pairing a lock with Vera.
  
2.  When Vera's power light comes on and starts double flashing, which means Vera is up but has no internet connection, hold down the black button on the back of Vera while tapping the red button.  Be careful not to hit the black (restore) button twice in a row, as this will reset the router to the [[Factory_Reset|factory default]] configuration.  Vera's power light blinks steadily 1 time per second.  Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat this sequence until it does.
+
Choose one of the following methods for adding a lock to Vera's network:
  
3.  Once Vera's power light is blinking steadily, meaning it's in 'add node' mode, then on the Schlage lock's keypad, enter the lock's program code followed by [schlage] and then 0.<br>
+
=== Method 1 - Vera is located FAR from the lock you are adding  ===
''Note: - you can find the lock's program code on the back of the lock or in it's manual;<br>''
+
''- after you press the lock's program code wait until you see the light blinking orange, then press [schlage] button and then 0.''
+
  
4. If the lock was successfully paired, Vera's power light will flutter, and shortly thereafter the 'schlage' light on the lock will blink green twice.  Reconnect Vera back where it belongs.
+
These are the steps typically used to pair secure Z-Wave devices with&nbsp;Vera.&nbsp; Note beforehand that this method involves Vera being disconnected from the internet as well as your home network.&nbsp; However, because Vera's Wi-Fi remains active throughout, you can perform Steps 7-9 by connecting your computer wirelessly to Vera.  
  
If the lock does not pair for some reason, repeat the process. If it still does not pair, try resetting the lock as follows:
+
1. Disconnect Vera and move Vera close to the Schlage lock. Plug Vera into an electrical outlet near the lock.
  
A. If Vera is still in 'add mode', meaning the power light is blinking slow and steady, tap the black button once.
+
2. After 60 seconds, Vera's power light comes on and starts double flashing - meaning Vera is operational but has no internet connection.  
  
B. Press and hold Vera's red button while you tap the black buttonVera's power light will blink fast steadily, about 3 times per second. Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat this sequence until it does.
+
3. Press-and-hold the black button on the back of Vera, then tap the red button once. (Be careful not to press the black ('restore') button twice in a row, as this will reset Vera to the [[Factory Reset|factory default]] configuration!) Vera's power light will begin blinking steadily once per second - meaning Vera is in 'Add' mode. (Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat Step 3 until it does.)
  
C. On the Schlage lock's keypad, enter the lock's program code followed by [schlage] and then 0.
+
4. On the Schlage lock's keypad, enter its 6-digit programming code.&nbsp; The light will blink orange.<br>''&nbsp;&nbsp;&nbsp; (Note: You can find the lock's program code on the back of the lock or in its manual.)''
  
D. The lock should beep and the 'Schlage' button on the lock should blink twice.  If it does not, try again starting with step A.  Then, when you have successfully reset the Schlage lock, go back to step 1 above and try again to include it in Vera's Z-Wave network.
+
5. Wait the lock to flash 3 times and to tone 3 times, then press the [Schlage] button, and then '0'.  
  
NOTE: When you reconnect Vera and go into the web page on the Devices tab, you should see the door lock. Assign it to a room, give it a name if you want, optionally set any other options, and click 'Save'.  After a few moments you will see Vera has the status 'Configuring ZWave devices', and Vera will be in the process of configuring the lock as evidenced by a blue spinning cog wheel.  It can take 10 minutes or so to configure the Schlage lock.  Be patient and don't use Vera for other tasks until eventually the cog will turn green if it was successful. Vera will not configure the lock again unless you change some settings for the lock.
+
6. If Vera's power light flutters briefly, and the lock's [Schlage] button blinks green twice, pairing was successful. Otherwise, you must follow the steps below for 'Resetting a Schlage Lock' and then repeat Steps 1-5 to try pairing the lock again
  
'''Method 2'''
+
7. Reconnect Vera back where it belongs (or connect to Vera wirelessly) and access Vera through your web browser.
  
Works great if your lock is near your PC or Laptop!
+
8. On Vera's 'Devices' page, assign the lock to a room and give it a name, and set any other options, then click 'Save'.
Log in to vera Locally 192.168.x.x you can use find vera but this wil work a bit faster!
+
  
1)Click " SETUP" in the top right hand corner of the Dashboard
+
9. Try activating (locking or unlocking) the door lock using Vera.
  
2)Click "DEVICES"
+
NOTE:&nbsp;If the lock fails to pair with Vera despite repeated attempts, try resetting the lock (see 'Resetting a Schlage Lock'), then attempt Steps 1-5 once again.
  
3)Click " Z-wave options"
+
(For more information on the method described here, read the 'Adding/Removing Z-Wave Devices' section of [[Buttons Indicators#Adding.2FRemoving_Z-Wave_devices|Adding/Removing Z-Wave Devices with the Red/Black Buttons]].)
  
4)Choose from the pull down menu "include" "one"  node "any" with "high power" and timeout after "30" seconds
+
=== Method 2 - Vera is located CLOSE to the lock you're adding ===
  
5)click "GO"  before entering the lock programming code make sure you are ready to pair the lock.
+
This method works best if your Vera unit is already positioned close enough to communicate with the Schlage door lock.  
be patient.
+
After you click "Go" enter the program code , then press "schlage" ( button on the lock) after it stops blinking amber press "0". You should get a green light.  
+
  
If you get red the lock may need to be uninstalled due to a error. This can happen with any Zwave device.Follow the same proceedure as above but choose "Exclude" in the drop down menu. If that still does not work don't give up you may need to reset the lock to factory default.  
+
1) Log in to Vera's interface by directing your computer's web browser to Vera's IP address (e.g. 192.168.81.1).<br>&nbsp;&nbsp;&nbsp; (Note: You can also log in using [http://FindVera.com FindVera.com], but the IP login works a bit faster.)
'''resetting the lock to factory default.'''
+
  
1) remove the batteries from the lock
+
2) Click 'SETUP' in the top right hand corner of the Dashboard.
  
2) on the lock press and release the "Schlage Button"
+
3) Click 'Devices'.
  
3) reconnect the battery(S)  
+
4) Click 'Z-Wave Options'.
  
4) wait until the Schalge button is no longer lit , Press and hold the Schalge button until it lights green and the lock beeps.  
+
5) From the pull-down menus, choose: "''Include''" "''one''" node "''any''" with "''high power''" and timeout after "''30''" seconds.  
  
Good luck
+
6) Before proceeding, have your lock's programming code handy and have a clear walking path to your lock.
  
post pairing notes;
+
7) Click 'Go' and immediately walk to the lock. (''You must complete Steps 6-8 within 30 seconds''.)
  
It takes quite some time after pairing to poll all 19 user codes. (even ones that are not set yet) So it may take a while to get the Green cog.  
+
8) On the lock's keypad, enter the 6-digit programming code, then press the [Schlage] button.  
You can see the event log by choosing
+
1) advanced tab
+
  
2) Logs  then choose Verbose and click "show Zwave Jobs"
+
9) After the [Schlage] button stops blinking amber and the 3 tones finishes, press '0'.&nbsp; The [Schlage] button should light up green, indicating that pairing with Vera was successful.<br>&nbsp;&nbsp;&nbsp; NOTE: If the [Schlage] button instead blinks red, the lock may need to be reset first. Repeat Steps 1-9, but choose "''Exclude''" in Step 5, to reset the lock. Then try to pair the lock again.  
If you see succesfull comunications to the lock you're in good shape. If you refresh you will see the progress.
+
  
=Usage=
+
10) On Vera's 'Devices' page, assign the lock to a room and give it a name, and set any other desired options, then click 'Save'.
  
==Lock/Unlock==
+
11) Try activating (locking or unlocking) the door lock using Vera.
  
You can lock/unlock the doorlocks and deadbolts the same way you turn on/off a light.  Note that with the doorlock, it can be locked and unlocked remotely.  But with the deadbolt, Schlage designed it so someone has to physically turn the deadbolt knob to engage/disengage the deadbolt.  When you choose either the lock or unlock button, the deadbolt knob is engaged for 10 seconds so someone can turn it, and then after 10 seconds, it's disengaged gage.  So you cannot remotely lock or unlock the deadbolt.  What you can do is wait until someone is at the door, then at that moment, click lock or unlock and tell them to turn the deadbolt.  Similarly, to remotely lock the deadbolt, there has to be someone at the door to do it.  This is the design of the Schlage deadbolt, and the function is the same with Schlage's bridge because there is no motor to lock/unlock the deadbolt.
+
NOTE:&nbsp;If the lock fails to pair with Vera despite repeated attemps with either method shown here, you may need to reset the lock to its factory default state before trying again&nbsp;(see 'Resetting a Schlage Lock to Factory Default', below).
  
==Controlling the lock with handheld remotes and scene controllers==
+
Once pairing has succeeded, Vera will begin configuring the lock you just added.&nbsp; During the configuration process, Vera will display a spinning blue cog icon next to the lock on Vera's 'Devices' page (see [[Device Control Status|Device Control Status]] for more details). It can take as long as 10 minutes for Vera to configure the lock completely, because a lot of encrypted data is being exchanged in the process. Be patient, and don't use Vera for other tasks until the green cog icon appears.&nbsp; Whenever you rename the lock, change its room, or otherwise change its&nbsp;configuration settings (other than assigning PIN codes), Vera will need to re-configure the lock again.
  
You can add handheld remotes and scene controllers and choose the option "Manage scenes as events".  Then you can create a scene which locks a door, as well as doing other tasks, and tie it to the button on the remote or in wall scene controller.  See [[ZWave_Add_Controller]] method #2.  So you can create a 'go to bed' scene, for example, which is button 1 on your scene controller, and which locks all the doors and turns off the lights and thermostats.  For your security, we only allow you to 'lock' the doors using a handheld remote or scene controller.  You cannot 'unlock' them with this technique because remotes and scene controllers are not secure devices and, therefore, there is the risk that an intruder could impersonate your handheld remote or scene controller. To unlock the doors, you must do this using the web interface or mobile phone interface.
+
== Resetting a Schlage Lock ==
  
==Scenes and events==
+
A. Disconnect Vera and move Vera close to the Schlage lock. Plug Vera into an electrical outlet near the lock.
  
The door locks fire events when the door is locked/unlocked, as well as when a user enters a pin code, and also when someone enters the wrong pin code 3 times in a row. You can create a scene, attach one of these events to the scene, and check one of the notify user boxes if you want to be notified of these events.
+
B. Vera's power light comes on and starts double flashing - meaning Vera is operational but has no internet connection.  
  
==Changing user codes==
+
C. Press-and-hold the red button on the back of Vera, then tap the black button once. Vera's power light will begin blinking fast, about 3 times per second - meaning Vera is in 'Remove' mode. (Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat Steps A-C until it does.)<br>
  
To create codes, type in a description name in the 'code named' box.  For example, "John" or "Pool service". Then type in the PIN code and click 'set'.  It may take up to 60 seconds for Vera to confirm the code was set, and once it does, you will see the new code (ie "John" or "Pool service") listed next to the device with a 'remove' button.  Click 'remove' to cancel that code.  Again, it may take 60 seconds for Vera to confirm the code was removed before it disappears from the list.  Just be patient, and try again if, after 60 seconds, Vera could not confirm the code was added or removed.  If there are already codes in the lock that you added yourself or using another Z-Wave controller, they will be shown as "Code 1", "Code 2", etc., and there is a 'remove' button to remove them.  If you want to add or remove lots of codes, you can do them all at once and you will see a 'job icon' for each new code.  You do not need to wait for each one to complete one at a time.  For example, you can program in 10 codes in rapid succession, and you will see 10 gray 'job icons'.  Gray means Vera hasn't started yet, as explained [[Device_Control_Status|here]].  Since it takes several seconds to program a new code into the lock, as each job is processed in order, and while it's in progress, the corresponding icon turns blue, and then becomes green when it is successful.  In this way, you can quickly queue up several new codes, and then just let Vera process them up one at a time.  When Vera is all done, you will see the list of all your codes with 'remove' buttons.  Similarly, you can click several remove buttons in rapid succession to queue up 'code removal' requests, without waiting for each one to complete one at a time.
+
D. On the Schlage lock's keypad, enter the lock's programming code.  
  
For your security, Vera does not keep a copy of the codes; they are only in the lock.
+
E. Press the [Schlage] button and then '0'. The lock should beep and the 'Schlage' button should blink twice, indicating the lock is now reset and ready to be paired with your Vera (see 'Adding/Pairing a Schlage Lock,' above).  
  
==Reversing the lock/unlock state==
+
If the lock fails to reset as described in Step E, try repeating Steps C-E until it does.
  
If the state of your door lock is backwards, meaning the dashboard shows it is locked when it's really unlocked and vice-versa, this can happen depending on the orientation of the lock when it was mounted.  To solve this, go to Vera's setup page, click the 'Devices' tab and click the '+' button next to the door lock, and then the advanced button.  If you see a parameter "#305 Reverse", enter a value of 1.  If you are sure parameter #305 is not in the list, then at the bottom where it says "New device data ID" put in 305 and in the "New device data value" put in 1, then click 'Add'.  Then save your changes.  Now Vera will reverse the lock/unlock status.
+
== Instructions for Vera1 ==
  
==Logging and camera links==
+
== Including a Schlage Lock ==
  
When you log in to findvera.com and click 'Events', you can select the door lock to see all the times someone entered a user code at the door or locked/unlocked the door.
+
Before adding a lock to your Z-Wave network, you may have to exclude it first from a previous network. Even if the lock is new, it could have come from the factory already paired with a Z-Wave network. To resolve this issue:
  
On the devices tab, click '+' next to your security cameras, and you will have a check box for this lock.  Then, whenever the door is locked/unlocked, Vera will also take a picture with the camera. You will see the pictures associated with an Event when you click the event on the findvera.com site.
+
Unplug the black Z-Wave dongle from the back of Vera.
 +
Tap once the dongle's button until the blue light starts blinking slow - 1 time pers second.
 +
On the lock's keypad, enter the programming code and wait for the light to blink orange.
 +
Press the [Schlage] button and then '0'.
  
=Security concerns=
+
== Excluding a Schlage Lock From Previous Network  ==
  
See: [[Security_Concerns]]
+
Before adding a lock to your Z-Wave network, you may have to [http://wiki.micasaverde.com/index.php/Reset_Node exclude] it first from a previous network. Even if the lock is new, it could have come from the factory already paired with a Z-Wave network.&nbsp;To resolve this issue:
 +
 
 +
#Unplug the black Z-Wave dongle from the back of Vera.
 +
#Keep the dongle's button pressed for 5 seconds, until the blue light starts blinking fast.
 +
#On the lock's keypad, enter the programming code and wait for the light to blink orange.
 +
#Press the [Schlage] button and then '0'.<br>
 +
 
 +
== Removing/Unpairing a Lock  ==
 +
 
 +
If your Schlage lock was mistakenly paired using Vera's normal (dongle-based) 'Include' procedure, the lock will have a red cog icon displayed next to it on Vera's 'Devices' page, and you won't be able to control it. To use the lock with Vera, you must first remove ("unpair")&nbsp;the lock from the Z-Wave network.
 +
 
 +
Remove the lock the same way as any other Z-Wave device:
 +
 
 +
(1)&nbsp;Remove Vera's black dongle, then hold the dongle near the lock.
 +
 
 +
(2) Press and hold the button on the dongle for 3 seconds until the light starts blinking fast, which indicates it's in 'Remove' mode.
 +
 
 +
(2) On the lock's keypad, enter the 6-digit programming code.&nbsp; The lock will beep audibly.
 +
 
 +
(3) Press the [Schlage] button followed by '0'.
 +
 
 +
(4) Re-insert the dongle in Vera, wait 60 seconds, and refresh the browser page.
 +
 
 +
The lock should now be gone from Vera's 'Devices' list, indicating the lock has been successfully removed from the network, and you can proceed to pair, or include, the lock the right way (see Method 1 or Method 2, above).
 +
 
 +
= Resetting a Schlage Lock to Factory Default  =
 +
 
 +
It is sometimes necessary to reset a Schlage lock to its factory default, in order to enable the lock to pair properly with Vera, or to resolve other lock malfunctions:<br>
 +
 
 +
1) Remove the batteries from the lock.
 +
 
 +
2) On the lock's keypad, press and release the [Schlage] button.
 +
 
 +
3) Reconnect the lock's battery(s).
 +
 
 +
4) Wait until the [Schlage] button is no longer lit.
 +
 
 +
5) ''Within 10 seconds'', press and hold the [Schlage] button until it lights green and the lock beeps.
 +
 
 +
Your Schlage lock is now reset to its factory default, and you may proceed to add it to Vera's network.
 +
 
 +
= Other Notes  =
 +
 
 +
Any time Vera configures a secure Z-Wave device such as a Schlage lock - either immediately after pairing the lock with Vera, or when subsequent changes are made to the lock's settings on Vera's 'Devices' page - Vera needs to poll all 19 of the lock's user codes, even ones that are not set yet!&nbsp; Accordingly, it may take Vera a while to display the green cog icon.&nbsp; Be patient, and do not use Vera for any other tasks during the configuration process.
 +
 
 +
You can see Vera's event log by choosing the 'Advanced' tab -&gt; 'Logs' -&gt; 'Verbose' -&gt; 'Show Z-Wave Jobs'.&nbsp; If Vera's communication with the lock has been successful, the list will show all completed events.&nbsp; Refresh the page using your web browser to see subsequent events as they are added to Vera's event log.<br>
 +
 
 +
= Using a Schlage Lock with Vera  =
 +
 
 +
== Lock/Unlock  ==
 +
 
 +
You can lock/unlock door locks and deadbolts with Vera the same way you turn a light On or Off. A door lock can be locked and unlocked remotely. '''But Schlage <u>deadbolts</u> are designed so someone has to physically turn the deadbolt knob to engage/disengage the deadbolt. When Vera tells the deadbolt to unlock, the deadbolt knob is engaged for 10 seconds so someone can turn it, and then after 10 seconds, it's disengaged again. '''(This behavior is identical to when you enter your PIN on the deadbolt's keypad.) Schlage locks contain no motor to lock/unlock the deadbolt. Thus, Vera cannot remotely lock or unlock a deadbolt for you. Instead, you can wait until someone is at the door, then click 'Lock' or 'Unlock' using Vera's interface, and tell the person to turn the deadbolt knob.
 +
 
 +
Vera offers three ways to control a door lock or deadbolt:
 +
 
 +
1) Use your PC's or PDA's web browser to click the lock/unlock buttons on Vera's 'Dashboard'. To allow remote access, you can click 'Unlock' when a person is in front of the door, giving the person a few seconds to manually turn the latch;
 +
 
 +
2) Use a cellphone application to activate the lock remotely; or,<br>
 +
 
 +
3) Issue a PIN to each authorized user (see 'Setting a User PIN,' below).
 +
 
 +
== Controlling the lock with handheld remotes and scene controllers  ==
 +
 
 +
You can add handheld remotes and scene controllers to Vera and choose the option "Manage scenes as events". Then you can create a scene which locks a door, as well as doing other tasks, and&nbsp;associate the scene&nbsp;to&nbsp;a button on the remote or in-wall scene controller. (See [[ZWave Add Controller|Z-Wave Add Controller]] method #2.) So you can create a 'Go to Bed' scene, for example, which&nbsp;may be&nbsp;button 1 on your scene controller, and which locks all the doors and turns off the lights and thermostats. For your security, we only allow you to 'lock' the doors using a handheld remote or scene controller. You cannot 'unlock' them with this technique because remotes and scene controllers are not secure devices and, therefore, there is the risk that an intruder could impersonate you using your handheld remote or scene controller. To unlock the doors, you must&nbsp;use Vera's web interface or mobile phone interface.
 +
 
 +
== Scenes and Events  ==
 +
 
 +
Door locks initiate events (a) when the door is locked/unlocked, (b) when a user enters a PIN, and (c) when someone enters the wrong PIN three times in a row. You can create a scene, associate one or more&nbsp;of these events&nbsp;with the scene, and check one of the 'Notify User' boxes if you want to be notified&nbsp;when&nbsp;an event (and a corresponding scene)&nbsp;happens.
 +
 
 +
If you're trying to create a scene to execute a command when a specific pin code is entered on the lock, when you go to set the event and select the event 'A PIN Code is entered', it will ask you to type in the ''''pin code number''''. The ''''pin code number'''' refers to the number in front of the pin codes on the door lock, so when you access the door lock settings and go to Pin Codes you can see a '''#x''' number (where x is from 1 to 7 if you have 7 pin codes for example). In the scene you have to specify only that number ('''x''') , without ''''#'''' (e.g. '''3''' ), thus without revealing the respective pin code number.
 +
 
 +
== Setting a User PIN  ==
 +
 
 +
You can create a PIN for each authorized user to use when locking/unlocking the door:
 +
 
 +
=== Adding a new PIN  ===
 +
 
 +
#Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
 +
#Select an empty slot for the new user
 +
#Give the user a descriptive name (e.g. "Pool Service")
 +
#Type the user's new PIN
 +
#Click 'Set'.
 +
#Each user's PIN will remain active until you remove it.
 +
 
 +
It may take up to 60 seconds for Vera to confirm the new code was set, whereupon you will see the new user listed next to the lock, along with a 'Remove' button.&nbsp; If the lock already contained user PINs - which you added manually or through a different Z-Wave controller - Vera will display them as "Code 1", "Code 2", etc.
 +
 
 +
NOTE: For your security, Vera does not keep a copy of the codes; they are only stored in the lock itself.
 +
 
 +
=== Changing an existing PIN  ===
 +
 
 +
#Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
 +
#Remove an existing user's slot (see below)<br>
 +
#Add the user again with a different PIN (see above)<br>
 +
#Click 'Set'. <br>
 +
#The user's PIN will remain active until you remove it.<br>
 +
 
 +
=== Removing a PIN  ===
 +
 
 +
#Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
 +
#From the list, find the user&nbsp;whose PIN you wish to de-activate
 +
#Click the 'Remove' button next to that user
 +
#Click 'Set'.
 +
#The user's PIN will&nbsp;be removed from Vera's list.
 +
 
 +
NOTE:&nbsp;If Vera does not confirm the removal after 60 seconds, simply try again.<br>
 +
 
 +
SPECIAL&nbsp;NOTE: If you add, change&nbsp;or remove many users/PINs in rapid succession, Vera will display a 'job icon' for each addition/change/deletion. You do <u>not</u> need to wait for each one to complete. For example, you can add 10 users in rapid succession, and you will see 10 gray 'job icons'. Gray indicates Vera hasn't started yet, as explained [[Device Control Status|here]]. Since it takes several seconds for Vera to program a new PIN into the lock, as each job is being processed (in order), the corresponding icon turns blue, then becomes green when it is successful. In this way, you can quickly queue up several new users, and then just let Vera process them one at a time. When Vera is finished, you will see the list of all users, along with a 'Remove' button next to each. Similarly, you can click several 'Remove' buttons in rapid succession without waiting for each removal to complete.
 +
 
 +
== Reversing the Lock/Unlock Status  ==
 +
 
 +
If the lock/unlock status of your door lock is backwards, meaning Vera's 'Dashboard' shows it is locked when it's really unlocked and vice-versa, it's possible the lock was oriented upside-down when mounted. To solve this issue, go to Vera's 'Setup' page, click the 'Devices' tab and click the '+' button next to the door lock, and then the 'Advanced' button. If you see a parameter "#305 Reverse", enter a value of '''1'''.&nbsp; Save this change. Vera will now reverse the lock/unlock status.
 +
 
 +
If parameter #305 is <u>not</u> in the list, then at the bottom of the page, type '''305''' in the "New Device Data ID" field, and type '''1''' in the "New Device Data Value" field. Click 'Add'. Then save your changes. Vera will now reverse the lock/unlock status.
 +
 
 +
== Logging and Camera Links  ==
 +
 
 +
When you log in to [http://FindVera.com FindVera.com] and click 'Events', you can select the door lock to see all the times someone entered a user code at the door or locked/unlocked the door.
 +
 
 +
On the 'Devices' tab, click '+' next to your security camera(s), and you will have a check box for this lock. Then, whenever the door is locked/unlocked, Vera will also take a picture with the camera(s). You will see the pictures associated with an Event when you click the event on the [http://FindVera.com FindVera.com] site.
 +
 
 +
= Security Concerns  =
 +
 
 +
See: [[Security Concerns]]
 +
 
 +
= External Links  =
 +
 
 +
*[http://part2.schlage.com/docs/manual_lock_programming-beta.pdf Schlage Lock User Manual]
 +
*[http://part2.schlage.com/docs/lock_user_guide.pdf Schlage Lock User Guide]

Latest revision as of 14:53, 20 April 2011

Contents

[edit] Secure Z-Wave Devices Explained

Door locks are a special breed of Z-Wave devices which require an exchange of security keys with Vera during the 'Include' ("pairing") process.  Accordingly, the normal 'Include' procedure - carrying Vera's black Z-Wave dongle to the device - will not work with Schlage locks.  Instead, Schlage locks must be paired with Vera using a special procedure (see 'Adding/Pairing a Lock', below).

In order for Vera to interoperate successfully with a Schlage lock or other secure Z-Wave device, the following conditions must all be met:

1) Vera's Z-Wave dongle must have a built-in security class:
Go to Setup -> Devices -> Z-Wave Options, and look at the 'Version'.
If the version is 2.40 your dongle does not have the security class implemented.  Request a replacement dongle by sending us a support request at the micasaverde.com website (click 'Support'), including your serial number, name, address and email.

2) Vera's firmware must be version 1.0.602 or later:
Go to Setup -> Advanced -> Download and confirm the version of your firmware.

3) The range for the Schlage lock is much less than for other devices because the antenna is inside a metal housing. The distance (in open air) between Vera and your lock should not exceed 30 feet (if you have two walls between them, the distance should be much lower). You can use a USB Cable extender to place Vera's Z-Wave dongle closer to the lock. (If you change the dongle position, don't forget to do a Heal Network after.) Otherwise you will need to add other modules to act as Z-Wave relays, as explained in #4.

4) Schlage locks work with Zensys' "Zensor Net Technology" which prolongs battery life for battery-powered Z-Wave devices. If the Schlage lock cannot be in direct communication to Vera and its signal must be routed through other Z-Wave devices, the last node in the route must be capable of "Zensor Net Beam" (ZNB). Many newer Z-Wave devices support Beaming, including:
I)any GE/Jasco lamp modules/switches with the following versions:
2.0a
3.0a
2.0b
3.0b
NOT 2, 2.0, 3, or 3.0
II) the Homepro ZDP100 lamp module (must be firmware version 3.3 or later). Also, after you've added lamp modules, you must do a Heal Network before they will effectively act as relays. Heal Network will also give you a report to confirm that Vera can talk to all your Z-Wave devices
III) and the Schlage RP200 light module. .

[edit] Setting Up a Schlage Lock with Vera

[edit] Adding/Pairing a Lock

Adding ("pairing") a secure device like the Schlage lock takes longer than adding a normal, non-secure device because Vera needs to share encryption keys with a secure device.  IMPORTANT: Leave Vera's black Z-Wave dongle inserted when pairing a lock with Vera.

Choose one of the following methods for adding a lock to Vera's network:

[edit] Method 1 - Vera is located FAR from the lock you are adding

These are the steps typically used to pair secure Z-Wave devices with Vera.  Note beforehand that this method involves Vera being disconnected from the internet as well as your home network.  However, because Vera's Wi-Fi remains active throughout, you can perform Steps 7-9 by connecting your computer wirelessly to Vera.

1. Disconnect Vera and move Vera close to the Schlage lock. Plug Vera into an electrical outlet near the lock.

2. After 60 seconds, Vera's power light comes on and starts double flashing - meaning Vera is operational but has no internet connection.

3. Press-and-hold the black button on the back of Vera, then tap the red button once. (Be careful not to press the black ('restore') button twice in a row, as this will reset Vera to the factory default configuration!) Vera's power light will begin blinking steadily once per second - meaning Vera is in 'Add' mode. (Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat Step 3 until it does.)

4. On the Schlage lock's keypad, enter its 6-digit programming code.  The light will blink orange.
    (Note: You can find the lock's program code on the back of the lock or in its manual.)

5. Wait the lock to flash 3 times and to tone 3 times, then press the [Schlage] button, and then '0'.

6. If Vera's power light flutters briefly, and the lock's [Schlage] button blinks green twice, pairing was successful. Otherwise, you must follow the steps below for 'Resetting a Schlage Lock' and then repeat Steps 1-5 to try pairing the lock again

7. Reconnect Vera back where it belongs (or connect to Vera wirelessly) and access Vera through your web browser.

8. On Vera's 'Devices' page, assign the lock to a room and give it a name, and set any other options, then click 'Save'.

9. Try activating (locking or unlocking) the door lock using Vera.

NOTE: If the lock fails to pair with Vera despite repeated attempts, try resetting the lock (see 'Resetting a Schlage Lock'), then attempt Steps 1-5 once again.

(For more information on the method described here, read the 'Adding/Removing Z-Wave Devices' section of Adding/Removing Z-Wave Devices with the Red/Black Buttons.)

[edit] Method 2 - Vera is located CLOSE to the lock you're adding

This method works best if your Vera unit is already positioned close enough to communicate with the Schlage door lock.

1) Log in to Vera's interface by directing your computer's web browser to Vera's IP address (e.g. 192.168.81.1).
    (Note: You can also log in using FindVera.com, but the IP login works a bit faster.)

2) Click 'SETUP' in the top right hand corner of the Dashboard.

3) Click 'Devices'.

4) Click 'Z-Wave Options'.

5) From the pull-down menus, choose: "Include" "one" node "any" with "high power" and timeout after "30" seconds.

6) Before proceeding, have your lock's programming code handy and have a clear walking path to your lock.

7) Click 'Go' and immediately walk to the lock. (You must complete Steps 6-8 within 30 seconds.)

8) On the lock's keypad, enter the 6-digit programming code, then press the [Schlage] button.

9) After the [Schlage] button stops blinking amber and the 3 tones finishes, press '0'.  The [Schlage] button should light up green, indicating that pairing with Vera was successful.
    NOTE: If the [Schlage] button instead blinks red, the lock may need to be reset first. Repeat Steps 1-9, but choose "Exclude" in Step 5, to reset the lock. Then try to pair the lock again.

10) On Vera's 'Devices' page, assign the lock to a room and give it a name, and set any other desired options, then click 'Save'.

11) Try activating (locking or unlocking) the door lock using Vera.

NOTE: If the lock fails to pair with Vera despite repeated attemps with either method shown here, you may need to reset the lock to its factory default state before trying again (see 'Resetting a Schlage Lock to Factory Default', below).

Once pairing has succeeded, Vera will begin configuring the lock you just added.  During the configuration process, Vera will display a spinning blue cog icon next to the lock on Vera's 'Devices' page (see Device Control Status for more details). It can take as long as 10 minutes for Vera to configure the lock completely, because a lot of encrypted data is being exchanged in the process. Be patient, and don't use Vera for other tasks until the green cog icon appears.  Whenever you rename the lock, change its room, or otherwise change its configuration settings (other than assigning PIN codes), Vera will need to re-configure the lock again.

[edit] Resetting a Schlage Lock

A. Disconnect Vera and move Vera close to the Schlage lock. Plug Vera into an electrical outlet near the lock.

B. Vera's power light comes on and starts double flashing - meaning Vera is operational but has no internet connection.

C. Press-and-hold the red button on the back of Vera, then tap the black button once. Vera's power light will begin blinking fast, about 3 times per second - meaning Vera is in 'Remove' mode. (Wait up to 30 seconds for Vera's power light to start blinking like this, and if it does not, repeat Steps A-C until it does.)

D. On the Schlage lock's keypad, enter the lock's programming code.

E. Press the [Schlage] button and then '0'. The lock should beep and the 'Schlage' button should blink twice, indicating the lock is now reset and ready to be paired with your Vera (see 'Adding/Pairing a Schlage Lock,' above).

If the lock fails to reset as described in Step E, try repeating Steps C-E until it does.

[edit] Instructions for Vera1

[edit] Including a Schlage Lock

Before adding a lock to your Z-Wave network, you may have to exclude it first from a previous network. Even if the lock is new, it could have come from the factory already paired with a Z-Wave network. To resolve this issue:

Unplug the black Z-Wave dongle from the back of Vera. Tap once the dongle's button until the blue light starts blinking slow - 1 time pers second. On the lock's keypad, enter the programming code and wait for the light to blink orange. Press the [Schlage] button and then '0'.

[edit] Excluding a Schlage Lock From Previous Network

Before adding a lock to your Z-Wave network, you may have to exclude it first from a previous network. Even if the lock is new, it could have come from the factory already paired with a Z-Wave network. To resolve this issue:

  1. Unplug the black Z-Wave dongle from the back of Vera.
  2. Keep the dongle's button pressed for 5 seconds, until the blue light starts blinking fast.
  3. On the lock's keypad, enter the programming code and wait for the light to blink orange.
  4. Press the [Schlage] button and then '0'.

[edit] Removing/Unpairing a Lock

If your Schlage lock was mistakenly paired using Vera's normal (dongle-based) 'Include' procedure, the lock will have a red cog icon displayed next to it on Vera's 'Devices' page, and you won't be able to control it. To use the lock with Vera, you must first remove ("unpair") the lock from the Z-Wave network.

Remove the lock the same way as any other Z-Wave device:

(1) Remove Vera's black dongle, then hold the dongle near the lock.

(2) Press and hold the button on the dongle for 3 seconds until the light starts blinking fast, which indicates it's in 'Remove' mode.

(2) On the lock's keypad, enter the 6-digit programming code.  The lock will beep audibly.

(3) Press the [Schlage] button followed by '0'.

(4) Re-insert the dongle in Vera, wait 60 seconds, and refresh the browser page.

The lock should now be gone from Vera's 'Devices' list, indicating the lock has been successfully removed from the network, and you can proceed to pair, or include, the lock the right way (see Method 1 or Method 2, above).

[edit] Resetting a Schlage Lock to Factory Default

It is sometimes necessary to reset a Schlage lock to its factory default, in order to enable the lock to pair properly with Vera, or to resolve other lock malfunctions:

1) Remove the batteries from the lock.

2) On the lock's keypad, press and release the [Schlage] button.

3) Reconnect the lock's battery(s).

4) Wait until the [Schlage] button is no longer lit.

5) Within 10 seconds, press and hold the [Schlage] button until it lights green and the lock beeps.

Your Schlage lock is now reset to its factory default, and you may proceed to add it to Vera's network.

[edit] Other Notes

Any time Vera configures a secure Z-Wave device such as a Schlage lock - either immediately after pairing the lock with Vera, or when subsequent changes are made to the lock's settings on Vera's 'Devices' page - Vera needs to poll all 19 of the lock's user codes, even ones that are not set yet!  Accordingly, it may take Vera a while to display the green cog icon.  Be patient, and do not use Vera for any other tasks during the configuration process.

You can see Vera's event log by choosing the 'Advanced' tab -> 'Logs' -> 'Verbose' -> 'Show Z-Wave Jobs'.  If Vera's communication with the lock has been successful, the list will show all completed events.  Refresh the page using your web browser to see subsequent events as they are added to Vera's event log.

[edit] Using a Schlage Lock with Vera

[edit] Lock/Unlock

You can lock/unlock door locks and deadbolts with Vera the same way you turn a light On or Off. A door lock can be locked and unlocked remotely. But Schlage deadbolts are designed so someone has to physically turn the deadbolt knob to engage/disengage the deadbolt. When Vera tells the deadbolt to unlock, the deadbolt knob is engaged for 10 seconds so someone can turn it, and then after 10 seconds, it's disengaged again. (This behavior is identical to when you enter your PIN on the deadbolt's keypad.) Schlage locks contain no motor to lock/unlock the deadbolt. Thus, Vera cannot remotely lock or unlock a deadbolt for you. Instead, you can wait until someone is at the door, then click 'Lock' or 'Unlock' using Vera's interface, and tell the person to turn the deadbolt knob.

Vera offers three ways to control a door lock or deadbolt:

1) Use your PC's or PDA's web browser to click the lock/unlock buttons on Vera's 'Dashboard'. To allow remote access, you can click 'Unlock' when a person is in front of the door, giving the person a few seconds to manually turn the latch;

2) Use a cellphone application to activate the lock remotely; or,

3) Issue a PIN to each authorized user (see 'Setting a User PIN,' below).

[edit] Controlling the lock with handheld remotes and scene controllers

You can add handheld remotes and scene controllers to Vera and choose the option "Manage scenes as events". Then you can create a scene which locks a door, as well as doing other tasks, and associate the scene to a button on the remote or in-wall scene controller. (See Z-Wave Add Controller method #2.) So you can create a 'Go to Bed' scene, for example, which may be button 1 on your scene controller, and which locks all the doors and turns off the lights and thermostats. For your security, we only allow you to 'lock' the doors using a handheld remote or scene controller. You cannot 'unlock' them with this technique because remotes and scene controllers are not secure devices and, therefore, there is the risk that an intruder could impersonate you using your handheld remote or scene controller. To unlock the doors, you must use Vera's web interface or mobile phone interface.

[edit] Scenes and Events

Door locks initiate events (a) when the door is locked/unlocked, (b) when a user enters a PIN, and (c) when someone enters the wrong PIN three times in a row. You can create a scene, associate one or more of these events with the scene, and check one of the 'Notify User' boxes if you want to be notified when an event (and a corresponding scene) happens.

If you're trying to create a scene to execute a command when a specific pin code is entered on the lock, when you go to set the event and select the event 'A PIN Code is entered', it will ask you to type in the 'pin code number'. The 'pin code number' refers to the number in front of the pin codes on the door lock, so when you access the door lock settings and go to Pin Codes you can see a #x number (where x is from 1 to 7 if you have 7 pin codes for example). In the scene you have to specify only that number (x) , without '#' (e.g. 3 ), thus without revealing the respective pin code number.

[edit] Setting a User PIN

You can create a PIN for each authorized user to use when locking/unlocking the door:

[edit] Adding a new PIN

  1. Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
  2. Select an empty slot for the new user
  3. Give the user a descriptive name (e.g. "Pool Service")
  4. Type the user's new PIN
  5. Click 'Set'.
  6. Each user's PIN will remain active until you remove it.

It may take up to 60 seconds for Vera to confirm the new code was set, whereupon you will see the new user listed next to the lock, along with a 'Remove' button.  If the lock already contained user PINs - which you added manually or through a different Z-Wave controller - Vera will display them as "Code 1", "Code 2", etc.

NOTE: For your security, Vera does not keep a copy of the codes; they are only stored in the lock itself.

[edit] Changing an existing PIN

  1. Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
  2. Remove an existing user's slot (see below)
  3. Add the user again with a different PIN (see above)
  4. Click 'Set'.
  5. The user's PIN will remain active until you remove it.

[edit] Removing a PIN

  1. Navigate to Vera's 'Control' (or 'Dashboard' or 'Devices') page
  2. From the list, find the user whose PIN you wish to de-activate
  3. Click the 'Remove' button next to that user
  4. Click 'Set'.
  5. The user's PIN will be removed from Vera's list.

NOTE: If Vera does not confirm the removal after 60 seconds, simply try again.

SPECIAL NOTE: If you add, change or remove many users/PINs in rapid succession, Vera will display a 'job icon' for each addition/change/deletion. You do not need to wait for each one to complete. For example, you can add 10 users in rapid succession, and you will see 10 gray 'job icons'. Gray indicates Vera hasn't started yet, as explained here. Since it takes several seconds for Vera to program a new PIN into the lock, as each job is being processed (in order), the corresponding icon turns blue, then becomes green when it is successful. In this way, you can quickly queue up several new users, and then just let Vera process them one at a time. When Vera is finished, you will see the list of all users, along with a 'Remove' button next to each. Similarly, you can click several 'Remove' buttons in rapid succession without waiting for each removal to complete.

[edit] Reversing the Lock/Unlock Status

If the lock/unlock status of your door lock is backwards, meaning Vera's 'Dashboard' shows it is locked when it's really unlocked and vice-versa, it's possible the lock was oriented upside-down when mounted. To solve this issue, go to Vera's 'Setup' page, click the 'Devices' tab and click the '+' button next to the door lock, and then the 'Advanced' button. If you see a parameter "#305 Reverse", enter a value of 1.  Save this change. Vera will now reverse the lock/unlock status.

If parameter #305 is not in the list, then at the bottom of the page, type 305 in the "New Device Data ID" field, and type 1 in the "New Device Data Value" field. Click 'Add'. Then save your changes. Vera will now reverse the lock/unlock status.

[edit] Logging and Camera Links

When you log in to FindVera.com and click 'Events', you can select the door lock to see all the times someone entered a user code at the door or locked/unlocked the door.

On the 'Devices' tab, click '+' next to your security camera(s), and you will have a check box for this lock. Then, whenever the door is locked/unlocked, Vera will also take a picture with the camera(s). You will see the pictures associated with an Event when you click the event on the FindVera.com site.

[edit] Security Concerns

See: Security Concerns

[edit] External Links

Personal tools