ZWave Add Controller

With most Z-Wave devices, you add them to Vera's Z-Wave network by clicking the 'Add other Z-Wave devices' on the devices tab in Vera's menu and following the instructions where you remove Vera's black Z-Wave dongle and carry it to your Z-Wave device. But, battery operated handheld remote controls are special cases. To add them you leave Vera's black dongle connected, bring them to Vera, and chose the 'Add Z-Wave controller' option instead. In general, when adding these handheld remotes, there are a few more steps, as explained below. Most in wall controllers that are connected to your house's electricity (ie not battery operated) can be added like any other Z-Wave device and do not to be treated specially like the battery operated controllers. See Supported controllers/gateways below for a list.

There are 2 ways you can get your Z-Wave handheld remotes and scene controllers to control other Z-Wave devices. Method #1 is the traditional Z-Wave method where you program a scene into the remote control. All Z-Wave remotes and scene controllers have their own built-in way of doing this. Vera can help with this. After you add the controller into Vera you can have Vera transfer the scenes to the controller for you. There are limitations with the traditional Z-Wave method. For example, scenes generally only work with lights, and will not let you control thermostats, arm sensors, and so on. So, Vera came up with a second method that is unique to Vera. Method #2 allows you to create scenes within Vera, which can do anything and control any device, and you can assign an event so the scene is triggered when a button on the controller is pushed. This gives you unlimited possibilities with your scenes. You can even add user notification so that when a button on a handheld remote is pressed, you get a text message.

Either way, the first step is to add the controller into Vera.

Adding battery operated handheld remotes to Vera

Add Z-Wave Controller Screen

When you want to add a handheld Z-Wave controller, go to Vera's setup page choose the "Devices" tab, and click the "Add ZWave controller" link or button. You will have 60 seconds to bring the handheld controller to within 3 feet (1 meter) of Vera and then to press the buttons on the handheld controller to add the controller to an existing ZWave network. This process is different for each handheld controller, and is often given different names. A chart of some popular ZWave handheld controllers is shown below along with the steps to add the controller to Vera, and what the process is called. Vera shows the status and progress in blue at the top of the page, starting with: "Running: Job is waiting: Ready...", which means Vera is waiting for your handheld controller to start.

If you cannot add the controller to Vera, it's possible the controller is already part of another Z-Wave network. In this case, you must first reset the controller before you can add it to Vera. Instructions for resetting some popular controllers is shown below.

Adding in-wall scene controllers to Vera

As mentioned above, in general you can add these devices like any other Z-Wave device and don't need to use the 'Add ZWave controller' link.

Method #1: Traditional scene assignments for controllers

Normally handheld controllers are battery operated, and, to save battery life, they do not allow Vera to talk to them to configure them except at the moment that Vera is adding them to the network. Many handheld controllers are programmable. For example, most have one or more button to activate "Scenes" or channels. Vera can help you configure your controller, such as assigning scenes to the buttons. To do this, you must first add the controller to Vera's ZWave network, so Vera knows about it, as explained above. Then you can use Vera's web UI to configure the controller and assign scenes.

For in-wall scene controllers that plug into permanent power Vera can transfer the scene assignments at any time. But for battery operated handheld remotes, to save battery life, they only let Vera transfer the scenes when they are being added. So, after the scene assignments are setup, you will need to go back to "Add ZWave controller" again, and repeat the process of adding the controller. It's okay to add the controller multiple times like this. The controller will not appear multiple times in Vera's device list. Vera knows that you already added the controller, and, so when you add it again, Vera will simply use that opportunity to update the controller with scene assignments and configuration. The only time you will have the same controller added more than once is if, after adding the controller to Vera, you press the buttons on the ZWave controller to 'reset it'. This clears out everything in the controller, including the unique ID Vera gave it. So that means if you then re-add the controller again, Vera will think it's a new controller and add it again, and you'll have the same controller listed twice in Vera's device list. It's easy to get rid of the old controller though; click the '+' button next to it and then click 'Permanently remove dead node' to remove it from Vera's ZWave network.

Note that this is using the traditional Z-Wave scenes, and most Z-Wave controllers cannot control anything but lights. If you want more flexible scenes, look at Method #2 below.

The step by step instructions for assigning scenes to your handheld controller are:

1. Create the scenes in Vera's web UI. See Scenes for instructions.
2. If this is an in-wall scene controller, add it like any other ZWave device and skip to step 5.
3. Otherwise, if it's a battery operated remote, then if the controller is not brand new, or if you have already paired ZWave devices to it or used it with another ZWave controller, press the buttons on the controller to do a "Reset" of it to clear out all the old data. See the chart below for help.
4. Click the "Add ZWave controller" button on Vera's device tab, and add the controller. See the chart below for help.
5. After the device is added, it should show up on Vera's Unassigned devices page. If not, click the "Devices" tab again. You will need to pick a room for the controller. Although most handheld controllers are battery operated and can be used throughout the house, Vera requires you to assign each device to a room. This is just to keep Vera's way of keeping the device list organized, and does not in any way limit what rooms you can use the controller in. It's just for your benefit to keep the device list manageable. So pick the room the controller will most often be stored in, and click 'Continue'.
6. Find the controller on the Device list, and click the '+' button next to the controller. Then click 'Custom ZWave Settings'. See ZWave configuration options for a full explanation of this page
7. Click 'Add Scene assignment'. In the 'Key' field, type a number to indicate which key on the handheld remote you want to assign a scene to. Some handheld remotes only have 1 scene button, so just put in '1'. Others have more than one, so put in the number of the button. Then choose the scene you want assigned to that button. Repeat this for all the scenes you want to assign to buttons.
8. When you are all finished, click the red 'Save' button to save your changes.
9. If this is a battery operated controller that you added with the 'Add ZWave Controller' link, then after your changes are saved, you can click 'Continue' and then go back to the 'Devices' tab and choose "Add ZWave controller" again. Do this just like you did the time before in step 3. Now when Vera re-adds the handheld controller, Vera will transfer the scenes to it.

--todoal: screen shot of 'add scene assignment', and also of controller with the '+' button pressed and showing the 'custom zwave settings' button.

Add Scene Assignment

Method #2: Vera's special way of handling scene assignments

Add the controller to Vera's Z-Wave network the same way. See steps 1-5 above. Next, click the '+' button next to the device and check the box 'Treat scene buttons as events'. This tells Vera to take over the scene buttons on the remote. Save your changes. If this is a battery operated handheld remote that you added with 'Add ZWave controller', you will need to add it again to Vera, because Vera can only program it to take over the scene buttons while it's being added. Read the notes above with method #1 and see step 9.

Once your scene controller or handheld remote is configured to let Vera take over scene management, then you can create your scenes in Vera like normal. The scenes can do anything and control any device. To make that scene trigger when you press a button on the remote, click 'Add Event' next to the scene, choose the event 'Scene button is pressed', then choose the scene controller or handheld remote from the device pull down, and lastly indicate which button number should trigger the scene. If there's only 1 button, just enter 1. You can repeat this process if you want to have multiple buttons on multiple controllers trigger the same scene. Save your data when you're done. There is no need to add battery operated handheld remotes again. You can now change the scenes and button assignments in Vera whenever you want.

If your scene control has one or more 'scene off' button, you can generally make those trigger a scene by adding an event with button 0. Note that if your remote control has more than 1 scene off button, Vera cannot know which one you pressed and all scene off buttons will trigger the event tied to 'button 0'.

Supported controllers/gateways

These devices are added by bringing the controller near Vera and choosing 'Add ZWave Controller'.

The add sequence is how you tell the controller to add to Vera. The reset sequence is how you clear the controller if it's already been added to another Z-Wave network and can't be added to Vera.

Manufacturer	Device Type	Model no.	Version	Specs	Product Review	Add Sequence	Reset Sequence	Notes
Cooper Wiring Devices	Handheld Controller	RFHDCSG		Link	Link	Menu, Settings, Replicate, Receive, From Unknown Controller	Menu, Settings, Reset	Works well with Vera. Can transfer devices from Vera to the handheld but doesn't transfer device names. Also very expensive.
Intermatic	Handheld Controller	HA07		Link				Read Intermatic_Handheld_Remotes
Wayne Dalton	Gateway	WDHA-12R	??	Link	Link			Shows as Z-Wave controller, a pain to sync with Homelink car remote, able to associate with devices. Can now turn on/off All Z-wave devices from car. This gateway is required for the 3-button remote sold by them. Translates commands to Z-Wave Scenes. As firmware 1.0.602 it's working with Vera, it's seen as a secondary controller.Vera needs to be configured so that it interprets the WDHA-12 as sending "Button Presses" instead of "Scene Activation" events.

These devices are added like normal Z-Wave devices where you choose 'Add other Z-Wave devices' on Vera's menu and bring Vera's ZWave dongle to the device

Manufacturer	Device Type	Model no.	Version	Specs	Product Review	Add Sequence	Reset Sequence	Notes
Cooper	5 Scene Controller	RFWDC						Read Cooper_Scene_Controller
Leviton	4 Scene Controller	RZCS4						Read Leviton_Scene_Controller
Leviton	1 Scene Controller	RZCZ1-1LX	Unknown	Link	Link	Link		Read Leviton_Scene_Controller

Unsupported / Partially supported controllers/gateways

Not working as of firmware version wl500gP-1.0.584.trx

Manufacturer	Model	Notes
Sylvania	SH50201	"all on" and "all off" buttons work but scene buttons are not supported at this time. 3/28/2009. To program this controller put vera in add controller mode and then hit "menu", then press right arrow until you see setup. Press ok. Righ arrow to copy remote control. Press ok. Right arrow to receive information and click ok. Wait for vera to confirm the controller was added.
ACT HomePro	ZTH100	Sylvania is a rebranded ACT Homepro "all on" and "all off" buttons work but scene buttons are not supported at this time. 3/28/2009.