UI5 Issues

From MiOS
(Difference between revisions)
Jump to: navigation, search
(New page: oTi@ - The upgrade wiped out the logs on the USB stick. - MiOS routing may have been automatically enabled? I'd have to downgrade to make sure it wasn't already automagically enabled bef...)

Revision as of 03:46, 29 August 2011

oTi@

- The upgrade wiped out the logs on the USB stick.

- MiOS routing may have been automatically enabled? I'd have to downgrade to make sure it wasn't already automagically enabled before the upgrade.

- No more sections?

- Can the sort order of stuff be changed?

- It looks like some of my scenes didn't carry over properly. (Dimmer settings lost.)

- When I tried to edit the scene remotely through cp.mios, I got a message saying: 'You are not allowed to save the settings on this system'.

- Switched to VPN and edited the scene; let me save it, but it doesn't look like it actually saved.

- Prefer a clock with seconds (or switchable on/off) and all digits the same size.

- I'd move the username over to the left, and remove the permanent 'Welcome:'.

- A quick 'info' button to pull up firmware versions (Vera and Z-Wave), IP, PRI status, etc. would be nice.

- Would like to be able to make the status window bigger and perhaps it can float, so all messages fit. It's an important window.

- Will wait for the new graphics, etc., but I still see a lot of 'dead' space, boxes are big, etc.

- The way stuff gets laid out on the screen seems unnatural, because dimmers are bigger than switches (i.e. it's not always left-aligned).

- Dimmers will show the percentages, right? (Especially useful when setting a scene.)

- I would love for the 'On' button on a dimmer to cause the dimmer to go the last setting, rather than full on, or some way at least to tell a dimmer to go the last setting. I've been missing this (and wrote a bug on it) a lot. (Currently working around it with a low-level basic set 255, followed by a poll.)

- Minimize the number of different font types. Probably just pick one for a consistent look and feel.

- (repeat) Devices > Sensor tab would be nice; somewhere towards the left. Motion/3-in-1/Door-Window stuff now shows up all the way to the right under Other. I imagine many folks may have some of these.

- What's Devices > Mobile Phones?

- Events/Timers get names. Given the various times it has come up on the forum, it seems intuitive for folks that you can then later refer to these events/timers and not have to define them again. I.e. defining 'Kitchen Motion Sensor Tripped' and 'Wednesday at 5pm' once. This probably has some UI design impact; but well, this is a new major version.

- SQRemote rejects version 1.5.56. That should probably be mentioned somewhere (or made compatible by SquareConnect) upon public release.

- When adding a device it is now not quite clear where to look for it / see what's going on. It'll show up as Other for a bit and then jump to whatever tab is appropriate, once Vera has configured it. Likely to confuse folks? (Example: add a relay; shows up in Other; than jumps to Lights.)

strangely

The turquoise and orange really don't work well with the rest of the colours.

Why is there still an annoying pop up when activating a scene?

You shouldn't have to click the wrench to view a camera.

Still no conditional expressions.

There should be another tab next to pinned devices in the dashboard that allows you to see all devices on one page without pinning.

Notification scenes are now showing up

Where are you supposed to set notifications?

When trying to edit a scene that involves my alarm plugin, there is no panel or partition device available under any of the category tabs

Scenes that involved the old advanced tab in UI4 don't seem to be editable or viewable anymore?

Standard scenes don't seem to editable either

There doesn't seem to be any way to see what the existing timers are? I'm not talking about scheduled timers, but more things like "after 2 hours turn off etc" which I've found out dont seem to work after migrating anyway.

Lights should be labeled lights and appliances, and if it's not possible to distinguish between these then the picture of a bulb should be editable.

Sensors do not visually show if tripped or not

What is the purpose of the small arrow highlighted in my attached picture, and why do some devices have these only on the bypass button only?

garretwp

Thermostat: shows my temperatures in C and not in F.

Thermostat: does not show the current temp.

Thermostat: fan mode still not working.

Notification of command sent does not clear

- The status window should be wider. There is all that space up top. Why not either get rid of the extra space or use it for the status window. That would allow us not have to scroll in the window.

- Yes, graphics are missing and will have to wait when they get finished and packed into the next firmware.

- The devices boxes should all be the same size and the alignments do get messed up. Attached image.

- Text in the devices that show information is too close to the veritical bar, it should be larger and darker in color.

- The idea of hitting the on button and having the dimmer go back to last state would be nice. (I am going to add that idea into my android application!)

- I guess the energy monitory will come shortly?


- oTi@ reported not all scenes carried over properly. I can also state the same. Especially the scenes that involve dimmers.

   - This also goes for thermostats as well

- Edit a scene that involves a dimmer and having the level set in the scene does not get saved.

- Schedules in the automation section should show the scene name that belongs to that schedule. I have similar schedule names for different scenes (e.g. wed). And looking at the schedule section shows a ton of wed names, but have no clue what scene owns that schedule.

- Formatting is messed up in the schedules section with having long names or long description. See attached image

Creating Scene to adjust my thermostat to a certain temperature does not save the temperature value.

Henk

1. All my "equipment" and scenes seem to work except my camera (will elaborate seperately).

2. USB logs are wiped ( but that also happened on UI4 upgrades)

3. i had some issues when removing a scene (bin didnt work) that were solved after a CTRL F5

4. There are some parts of the menu that seem " unfinished" as in the text is black (default?) and not in line with the overal theme. This occurs especially in the settings tab.

5. My SM103 doorsensor does not show up in climate& security but in "other devices" where most custom plugins reside. In fact, why is there not a secion for "Motorized control" to sort window coverings etc in?

6. Pinned scenes do not "stick" even after saves. the show up unpinned after a refresh. i LOVE the breakout of scenes triggers and schedules. It made me aware that i had not named a few of them at all.

7. The button under create/save is merely invisible and therefore unreadable. After clicking the edge that WAS visible, i found out it was a "return home button"  ?

1. In devices i miss an ALL devices tab

2. My camera plugin did not show snapshot (had that on UI4 for a while too) Worse, also streaming was broken (worked flawlessly on UI4). I decided to remove the plugin completely and build it from scratch. Will report my findings later!

1. Hide / autocollapse emtpy rooms from any view as to not confuse users and claim more realastate for important info.

1. Apps/plugins installed under UI4 that get migrated to UI5 do not show version number. Workaround is to remove the plugin/app and reinstall it in UI5 using the new APPS section

am having trouble with luup code in events. the same luupcode for a binary light switch works. 1 binary Duewi light switch send notification via Prowl when lights go OFF notification works when lights shut OFF., 1 FCM luup plugin (works) Scene to pickup events from the plugin (LUUP) Event for the scene coded to send notification via prowl (same code as before and similar to the luup event for the binary switch, worked under UI4).

Notification does not work!

1. Missing and corrupted scenes after migration 2. LUUP code not working anymore after migration although the code itself is intact (luup events) 3. I have seen information from one plugin depicted in another (weather depicting FCM caller data) 4. I have noticed scenes to pop up unexpected and ive had scenes that were hard to delete, only refreshing, reloading and trying time after time made it work. 5. Pinning of scenes doesnt work (after a save and reload they are gone from the pinning list.

Vera started acting up, she switched my binary plugin module off time after time when i switched it on manually at the device, using the device ON/OFF button.

mario23

all scene settings didn't make it over. Also, how do I now set a scene conditions like before. Example, Turn dimmer to 50% for two hours then down to 20%???

Saving settings in some scenes aren't working for me.

Ap15e

Archive old logs: might have been activated by upgrade to UI5

trash bins for devices and for scenes are at different positions - absolutely unacceptable!
auto-layout should use fixed width/height for device boxes 
device boxes are too large, current layout is unusable if there are > 10 devices
scene boxes are too large, current layout is unusable if there are > 15 scenes
motion sensors and smoke sensors are "Other" devices
Help is empty
Control Panels for all devices auto-close after less than a second
Add Devices -> most of the Add buttons don't work
Personal tools