How to reset to default network settings

From MiOS
(Difference between revisions)
Jump to: navigation, search
Line 8: Line 8:
  
 
             Open Control Panel
 
             Open Control Panel
          View by: Large icons -> Network and Sharing Center
+
          View by: Large icons -> Network and Sharing Center
          View by: Category -> View netork status and tasks
+
          View by: Category -> View netork status and tasks
          Click on Change adapter settings
+
          Click on Change adapter settings
          Right click on LAN connection to Vera , then click on Properties
+
          Right click on LAN connection to Vera , then click on Properties
          Highlight the Internet Protocol Version 4 (TCP/IPv4) item, and click on Properties
+
          Highlight the Internet Protocol Version 4 (TCP/IPv4) item, and click on Properties
          In the IP address field enter 192.168.81.10
+
          In the IP address field enter 192.168.81.10
          In the subnet mask field enter 255.255.255.0
+
          In the subnet mask field enter 255.255.255.0
          In the Default gateway field enter 192.168.81.1
+
          In the Default gateway field enter 192.168.81.1
          Click OK
+
          Click OK
          Click OK Again
+
          Click OK Again
  
 
*In '''Windows XP'''
 
*In '''Windows XP'''
  
 
             Open Windows Start menu.
 
             Open Windows Start menu.
          Open Control Panel.
+
          Open Control Panel.
          Classic view: Open Network Connections
+
          Classic view: Open Network Connections
          Category view: Select Network and Internet Connections, and then Network Connections.
+
          Category view: Select Network and Internet Connections, and then Network Connections.
          Double-click on your the LAN connection to Vera.
+
          Double-click on your the LAN connection to Vera.
          Click Properties.
+
          Click Properties.
          In the General tab, highlight the Internet Protocol (TCP/IP) item, and click Properties.  
+
          In the General tab, highlight the Internet Protocol (TCP/IP) item, and click Properties.  
          In the IP address field enter 192.168.81.10
+
          In the IP address field enter 192.168.81.10
          In the subnet mask field enter 255.255.255.0
+
          In the subnet mask field enter 255.255.255.0
          In the Default gateway field enter 192.168.81.1
+
          In the Default gateway field enter 192.168.81.1
          Click OK
+
          Click OK
          Click OK again
+
          Click OK again
  
 
*In '''Mac OS X'''
 
*In '''Mac OS X'''
  
 
             Open the Apple Menu(Top left corner of your screen)
 
             Open the Apple Menu(Top left corner of your screen)
          Click System Preferences
+
          Click System Preferences
          Click Network
+
          Click Network
          Click the Locations dropdown and select Edit Locations
+
          Click the Locations dropdown and select Edit Locations
          Click the plus sign and call your new location "Vera system Troubleshooting"
+
          Click the plus sign and call your new location "Vera system Troubleshooting"
          Select "Ethernet" from the list on the left
+
          Select "Ethernet" from the list on the left
          Select "Manually" from the Configure IPv4 dropdown
+
          Select "Manually" from the Configure IPv4 dropdown
          Enter 192.168.81.10 in the IP address field
+
          Enter 192.168.81.10 in the IP address field
          Enter 255.255.255.0 in the subnet mask field
+
          Enter 255.255.255.0 in the subnet mask field
          Enter 192.168.81.1 in the Router field
+
          Enter 192.168.81.1 in the Router field
          Hit "Apply"
+
          Hit "Apply"
  
- Unplug Vera from the power cord - Unplug all the cables from Vera - Plug a network cable from your computer into Vera's LAN port  
+
- Unplug Vera from the power cord  
 +
 
 +
- Unplug all the cables from Vera  
 +
 
 +
- Plug a network cable from your computer into Vera's LAN port  
  
 
           Vera 2    -> eth2 port
 
           Vera 2    -> eth2 port
          Vera 3    -> lan port (port number 1)  
+
        Vera 3    -> lan port (port number 1)  
          Vera Lite -> ethernet port
+
        Vera Lite -> ethernet port
  
 
- Plug Vera into the power cord  
 
- Plug Vera into the power cord  

Revision as of 11:31, 12 July 2013

How to reset to default network settings on UI5

By default Vera automatically configures its network, if you connect it to your router it will automatically configure in switch mode. If after plugging Vera into your network, you don't see your Vera on cp.mios.com , please follow these steps to fix your networking:

- Put a STATIC IP to your computer.

  • In Windows 7
           Open Control Panel
         View by: Large icons -> Network and Sharing Center
         View by: Category -> View netork status and tasks
         Click on Change adapter settings
         Right click on LAN connection to Vera , then click on Properties
         Highlight the Internet Protocol Version 4 (TCP/IPv4) item, and click on Properties
         In the IP address field enter 192.168.81.10
         In the subnet mask field enter 255.255.255.0
         In the Default gateway field enter 192.168.81.1
         Click OK
         Click OK Again
  • In Windows XP
           Open Windows Start menu.
         Open Control Panel.
         Classic view: Open Network Connections
         Category view: Select Network and Internet Connections, and then Network Connections.
         Double-click on your the LAN connection to Vera.
         Click Properties.
         In the General tab, highlight the Internet Protocol (TCP/IP) item, and click Properties. 
         In the IP address field enter 192.168.81.10
         In the subnet mask field enter 255.255.255.0
         In the Default gateway field enter 192.168.81.1
         Click OK
         Click OK again
  • In Mac OS X
           Open the Apple Menu(Top left corner of your screen)
         Click System Preferences
         Click Network
         Click the Locations dropdown and select Edit Locations
         Click the plus sign and call your new location "Vera system Troubleshooting"
         Select "Ethernet" from the list on the left
         Select "Manually" from the Configure IPv4 dropdown
         Enter 192.168.81.10 in the IP address field
         Enter 255.255.255.0 in the subnet mask field
         Enter 192.168.81.1 in the Router field
         Hit "Apply"

- Unplug Vera from the power cord

- Unplug all the cables from Vera

- Plug a network cable from your computer into Vera's LAN port

          Vera 2    -> eth2 port
        Vera 3    -> lan port (port number 1) 
        Vera Lite -> ethernet port

- Plug Vera into the power cord

- Wait it to start

Now open an web browser and type this in the address bar: 192.168.81.1
Now you can see the DASHBOARD page of your Vera unit.

Go to SETUP > Net & Wifi Click on the blue button "reset to default network settings"

Now will reset to default network settings, that can take up to 5 minutes.

Now you can unplug Vera unit from your pc and plug it to the internet.


Personal tools