Aeon 4in1

From MiOS
(Difference between revisions)
Jump to: navigation, search
 
(2 intermediate revisions by one user not shown)
Line 1: Line 1:
<span style="color: rgb(255, 0, 0);">Note (October 2012): due to a change of the firmware in the production version of the Aeotec 4-in-1, it has been reported that the sensor is not currently fully functional in combination with Vera running firmware 1.5.408. (A private beta version of the Vera firmware appears to resolve this. If you want the private beta version, send us an email at support@micasaverde.com or submit a trouble ticket)
+
To use the Aeotec 4-in-1 MultiSensor with Vera, the following firmware is required:  
Aeotec has released a new firmware version for this 4-in-1 multi-sensor and to upgrade to it, use this tool: http://aeotec.com/partner/z-wave-firmware/viewcategory/7-multisensor
+
</span>
+
  
The Aeon 4-in-1 multi-sensor is supported in firmware versions over 1.1.1280. It appears as 4 devices: a motion sensor, a light sensor, a humidity sensor, and a temp sensor.  
+
- Aeotec MultiSensor firmware 1.18 [http://aeotec.com/partner/z-wave-firmware/viewcategory/7-multisensor]
  
To include the sensor, choose Add Device on your MIOS system, and then tap the black button by the battery compartment.&nbsp; Once it appears in your system, if it is not yet configured, hold the black button for 3 seconds and release. &nbsp; This causes the sensor to wake up so it can be configured, at which point it will appear as 4 devices.  
+
- Vera firmware 1.5.622 [http://cp.mios.com/firmware/]
  
Once the sensor is configured, you can hold the black button for 3 seconds again to force it to wake up so it can be polled for the temperature, humidity, light level, and motion sensor trip status.&nbsp; Note that it will only be polled once every 10 minutes to conserve the batteries.&nbsp; To force a poll on the next wakeup click the 'Poll Now' button on the MIOS dashboard for the motion sensor device.  
+
[[Image:Aeotec 4-in-1 1.png]]
 +
 
 +
<br>
 +
 
 +
To include and configure the MultiSensor, execute the following steps within 10 minutes:
 +
 
 +
1. Insert batteries into the MultiSensor.
 +
 
 +
2. Put Vera in inclusion mode.
 +
 
 +
3. Tap the black button on the MultiSensor.
 +
 
 +
Vera should detect the MultiSensor and the GUI will reload. After this, the motion part will be shown and the message ''Waiting for wakeup to configure device''.
 +
 
 +
[[Image:Aeotec 4-in-1 2.png]]
 +
 
 +
<br>
 +
 
 +
4. Tap the black button on the MultiSensor.
 +
 
 +
Vera will configure the MultiSensor and the GUI will reload. After this, all four sensor parts are shown, without values.
 +
 
 +
[[Image:Aeotec 4-in-1 3.png]]
 +
 
 +
<br>
 +
 
 +
5. On the ''Settings'' tab of the motion sensor part select ''Poll now''.
 +
 
 +
[[Image:Aeotec 4-in-1 4.png]]
 +
 
 +
<br>
 +
 
 +
Vera should poll the MultiSensor.
 +
 
 +
[[Image:Aeotec 4-in-1 5.png]]
 +
 
 +
<br>
 +
 
 +
6. Reload the browser page.
 +
 
 +
Sensor values should show. Initial setup is now complete. The MultiSensor should be fully functional. The default motion timeout is 4 minutes. Sensor values will be updated every 3 hours (approximately).
 +
 
 +
[[Image:Aeotec 4-in-1 6.png]]
 +
 
 +
<br>
 +
 
 +
The default wake-up interval is 28 minutes. If sensor value updates with every wake-up are desired, instead of every 3 hours, the minimum poll interval should be changed.
 +
 
 +
7. On the ''Settings'' tab of the motion sensor part, change the ''Poll this node at most once every'' value to 60.
 +
 
 +
[[Image:Aeotec 4-in-1 7.png]]
 +
 
 +
<br>
 +
 
 +
The default motion timeout is 4 minutes. A different value can be selected.
 +
 
 +
8. On the ''Device Options'' tab of the motion sensor part, change the ''Motion timeout'' (variable 3) to the desired value.<br>[An example of 10 seconds is shown.]
 +
 
 +
[[Image:Aeotec 4-in-1 8.png]]
 +
 
 +
<br>
 +
 
 +
9. Click the red Save button.
 +
 
 +
Vera reloads and ''Waiting for wakeup to configure device'' is shown again.
 +
 
 +
10. Tap the black button on the MultiSensor.
 +
 
 +
Vera configures the MultiSensor and the GUI will reload.
 +
 
 +
11. Reload the browser page.
 +
 
 +
12. Verify the minimum poll interval is set to the correct value.
 +
 
 +
[[Image:Aeotec 4-in-1 9.png]]
 +
 
 +
<br>
 +
 
 +
13. Verify the motion timeout variable ''Current Value'' matches the ''Desired Value''.
 +
 
 +
[[Image:Aeotec 4-in-1 10.png]]
 +
 
 +
<br>
 +
 
 +
14. Rapidly triple click the black button on the MultiSensor.
 +
 
 +
The MultiSensor is now in a low-power state and the red LED will be off. It is ready for use.  
  
 
[[Category:Hardware]]
 
[[Category:Hardware]]

Latest revision as of 21:54, 28 March 2013

To use the Aeotec 4-in-1 MultiSensor with Vera, the following firmware is required:

- Aeotec MultiSensor firmware 1.18 [1]

- Vera firmware 1.5.622 [2]

Aeotec 4-in-1 1.png


To include and configure the MultiSensor, execute the following steps within 10 minutes:

1. Insert batteries into the MultiSensor.

2. Put Vera in inclusion mode.

3. Tap the black button on the MultiSensor.

Vera should detect the MultiSensor and the GUI will reload. After this, the motion part will be shown and the message Waiting for wakeup to configure device.

Aeotec 4-in-1 2.png


4. Tap the black button on the MultiSensor.

Vera will configure the MultiSensor and the GUI will reload. After this, all four sensor parts are shown, without values.

Aeotec 4-in-1 3.png


5. On the Settings tab of the motion sensor part select Poll now.

Aeotec 4-in-1 4.png


Vera should poll the MultiSensor.

Aeotec 4-in-1 5.png


6. Reload the browser page.

Sensor values should show. Initial setup is now complete. The MultiSensor should be fully functional. The default motion timeout is 4 minutes. Sensor values will be updated every 3 hours (approximately).

Aeotec 4-in-1 6.png


The default wake-up interval is 28 minutes. If sensor value updates with every wake-up are desired, instead of every 3 hours, the minimum poll interval should be changed.

7. On the Settings tab of the motion sensor part, change the Poll this node at most once every value to 60.

Aeotec 4-in-1 7.png


The default motion timeout is 4 minutes. A different value can be selected.

8. On the Device Options tab of the motion sensor part, change the Motion timeout (variable 3) to the desired value.
[An example of 10 seconds is shown.]

Aeotec 4-in-1 8.png


9. Click the red Save button.

Vera reloads and Waiting for wakeup to configure device is shown again.

10. Tap the black button on the MultiSensor.

Vera configures the MultiSensor and the GUI will reload.

11. Reload the browser page.

12. Verify the minimum poll interval is set to the correct value.

Aeotec 4-in-1 9.png


13. Verify the motion timeout variable Current Value matches the Desired Value.

Aeotec 4-in-1 10.png


14. Rapidly triple click the black button on the MultiSensor.

The MultiSensor is now in a low-power state and the red LED will be off. It is ready for use.

Personal tools