Supported Hardware

From MiOS
Revision as of 14:40, 2 April 2012 by Mcv.adi (Talk | contribs)

Jump to: navigation, search

This is a page for Supported Z-Wave devices.

Alternative hardware pages exist for

In general, any device with the Z-Wave logo should work with Vera. A list of tested Z-Wave devices is below, with specific notes for each type of device. This is a wiki, so feel free to add to the page. To learn about Z-Wave routing and fixing routing problems see: Heal Network

Contents

Hardware Reported to Work

  • We strongly encourage users to list any and all products they tested and installed.
  • If a product works but you did not like it, please list it anyway. It may be the only product available to some users.


IMPORTANT! The devices listed here have been added by installers, technicians and users like yourself. Results may vary upon installations. MiCasaVerde does not guarantee operation and compatibility with your installation. The listed devices were found to work with their specific installation. Mixing different series and brands of equipment is not guaranteed in any way to work with other series and brands. It is very likely that users have not fully tested all features of the devices, so it is possible that a device listed here as compatible, will not prove compatible with your hardware. If you are editing this wiki DO NOT REMOVE a listed working device if it hasn't worked for you. Seek help to get the device to work under your individual circumstance. If you are adding to this wiki, please provide links to data for the device and add any tips you feel may benefit someone wanting to implement the device into an installation.


Lighting Devices

Manufacturer Device Type Model no. Version Date Purchased Location (indoor/outdoor) Specs Product Review Added by User Notes
ACT 2-way Dimmer Switch ZDW120
Nov 2008 Indoor Link Link WSeverino Works well, easy to install, LED is a very bright blue....can be programmed to be off when the light is off or on. "series 200" model supports Group Associations 2 & 3. (The older "series 100" supported Groups 1-4, but is no longer available.)
ACT 3-way Dimmer Switch ZDW103
Nov 2008 Indoor Link Link WSeverino Works well, can be tricky to install due to the different combination of 3 way circuits, LED is a very bright blue....can be programmed to be off when the light is off or on.
ACT 2-wire Dimmer Switch ZDW232
Jul 2010 Indoor Link Link Newb Wall-mount, 230v, 500W, 2-Wire (no neutral), works well. Can be programmed to be off when the light is off or on.
ACT 2-way Relay Switch ZRW113
Nov 2008 Indoor Link Link WSeverino Controls Florescent Lamps very well! No humming at all.
ACT Companion Switch AS101
Nov 2008 Indoor Link Link WSeverino Works well, can be tricky to install due to the different combination of 3 way circuits, The trick here is to install this device where the power comes in.
ACT
 3-way Dimmer Switch, 2 rocker
 ZDM230
 1.1
 Aug 2009
 Indoor
 Link
TedStriker
 Dimmer, Wall-mount, 230v, 500W,
3-way, 3 Wire, 2 rocker
ACT 3-way Relay Switch, 2 rocker ZRM230
 1.1
 Aug 2009
 Indoor
 Link
TedStriker
 Relay, Wall-mount, 230v, 6A,
3-way, 3 Wire, 2 rocker - Status polling does not work with Vera
Cooper Accessory (3-way slave)


Indoor


See Cooper Accessory Slave
Düwi 2 wire dimmer

July 2011 Indoor

intveltr In-wall dimmer.
Düwi 3 wire switch 05431
July 2011 Indoor

intveltr In-wall switch.
Düwi 3 wire switch 06431
July 2011 Indoor

intveltr The newer in-wall Düwi switch (also designated Düwi.me), marked with a green sticker on the housing. This switch supports status push.
Fibar 3 wire double switch FGS221
Oct 2011 Indoor

intveltr This device is designed to use (and be mounted behind) existing light switches. Supports status push. Also available: single switch, dimmer, blind control.
GE/Jasco Lamp Module w/Dimmer 45602   7/2011 Indoor       Works with most incandescent bulbs.
GE/Jasco Fluorescent Light & Appliance Module 45603   7/2011 Indoor       Works with small appliances, incandescent, fluorescent and LED bulbs.
GE/Jasco Outdoor Switch Module 45604   7/2011 Outdoor       Works with small appliances, incandescent, fluorescent and LED bulbs.
GE/Jasco On/Off/Dim Dimmer Switch 45606   2/2011 Indoor Link Link   Anthonyris Discontinued, See 45612. Requires neutral lead. Works fine with most bulbs. With Philips AmbientLED, flickers at >95% brightness. Supports beaming. Flickers at low-levels with dimmable LED.
GE/Jasco Dimmer Switch 45607     Indoor        
GE/Jasco On/Off Switch 45609   7/2011 Indoor        
GE/Jasco Auxiliary Switch 45610   7/2011 Indoor       No zwave function; for 3 and 4-way switching kits
GE/Jasco 2-way Rocker Dimmer 45612   2/2012 Indoor       No neutral required; replaces 45606
GE/Jasco 3-way Dimmer Kit 45613     Indoor       Possible error in 45613 manual diagrams, see 45610 diagrams
GE/Jasco 3-way Switch Kit 45614   7/2011 Indoor        
Innovus Relay Switch Adapter RAone SmartPower   Aug 2009 Indoor Link   TedStriker Works very well + it has a build in powermeter which works perfect with Vera
Innovus Dimmer Switch Adapter RAone SmartDimmer   Aug 2009 Indoor Link   TedStriker Works very well + it has a build in powermeter which works perfect with Vera
Intermatic Lamp Module HA03C   Sept 2010 Indoor Link
JonnyO Easy to Instal, supports dimming
Intermatic Screw-in Lamp Module HA05C
Nov 2008 Indoor/Outdoor Link Link WSeverino Easy install, easy to pair with Vera!
Intermatic 300 watt dimmer HA06
July 2007 Indoor Link

Affordable Dimmer Switch. incandescent/halogen only. Loads for 300 watts or less no neutral required. Great for dimming one bulb.
Intermatic 3-way Switch HA18
Dec 2008 Indoor Link
Kozanator Affordable 3-way Switch
Intermatic 3-way Dimmer Switch HA20
Nov 2008 Indoor Link Link
Affordable 3-way 600W dimmer
Leviton Dimmer Switch VRI06-1LX   Aug 2009 Indoor Link
guessed Works well
Leviton 4-Scene Controller with Switch VRCS4-MRX 7,2,67,0,2 Aug 2009 Indoor Link
guessed Works well, pair as per Leviton 4-Scene Controller, then again holding "2" and "4" to pair the Switch ("Load") itself.
Leviton Dimmer Switch VRM10-1LX 1 Nov 2008 Indoor Link Link mark-hc This is a high quality dimmer geared towards high-end installations
Leviton Scene capable 3-way switch (non-dimming) VRS15-1L   May 2011 Indoor Link
DaveL17 (Coordinating Remote??)
Leviton Scene capable 3-way switch (non-dimming) VRS15-1LX   Oct 2011 Indoor Link
DaveL17 Works well. Pair normally. Can also be used in single pole applications. [Note: white, ivory, Almond.]
Leviton Scene capable 3-way switch (non-dimming) VRS15-1LZ     Indoor Link
DaveL17 Works well. Pair normally. Can also be used in single pole applications. [Note: white, ivory, Light almond.]
Merten Radio sensor cover for dimmer inserts 5026xx, 5036xx, 5046xx 6,2,7,1,5 Apr 2009 Indoor Link   Ap15e Works well
Merten Radio sensor cover for switch inserts 5024xx, 5034xx, 5044xx 6,2,27,2,2   Indoor Link   Ap15e Works well
Merten Single Radio flush-mounted receiver 507001 6,2,27,2,2 Apr 2009 Indoor Link   Ap15e Works well
Merten switch, flush-mounted 507501, 507601     Indoor Link   Ap15e Works well (according to Link)
Merten 1-gang universal dimmer, flush-mounted 507900     Indoor Link   Ap15e Works well (according to Link)
Monster 4-Scene Controller with Switch IWC600 Dec 2011 Indoor Link
This is the same as the Leviton scene controller. Follow these instructions: Leviton 4-Scene Controller
Schlage Lamp Module RP200 1.0 Aug 2009 Indoor Link
LibraSun Works well
Sold with Schlage LiNK lock system


Plug & Receptacle Devices

Manufacturer Device Type Model no. Version Frequency Date Purchased Location (indoor/outdoor) Specs Product Review Added by User Notes
ACT In-Wall Receptacle ZRR150W 2.2   Nov 2008 Indoor Link Link
Works like a champ! Easy to Install. One receptacle RF controlled, the other is hot
ACT In-Wall Receptacle ZRP200   EU July 2011 Indoor     intveltr Basic plug-in switch.
ACT In-Wall Receptacle ZDP200   EU July 2011 Indoor     intveltr Basic plug-in dimmer.
Cooper Wiring Devices In-Wall Receptacle RFTR9505-T       Indoor Link

One receptacle is RF controlled, the other is hot
Duwi Z-Wave switch 3500 W 05437   EU Feb 2009 Indoor Link
ezhome High quality Plug-in switch, Easy install and works well
Everspring Z-Wave switch 3500 W AN157-2 4,2,64,1,2 EU   Indoor Link
Ap15e Works well.
Everspring Z-Wave switch 3500 W AN158   EU   Indoor  
intveltr Works well. Supports status push and power metering
GE/Jasco In-wall Duplex Receptacle 45605   US 2/2011 Indoor Link Link   Anthonyris Easy. Works.
Home Manageables Lamp Module (Dimming) HM-LM001     Nov 2011 Indoor 200W maximum load, 25W minimum load Link DaveL17 Works well. Support for incandescent loads only. Not load sensing.
Intermatic In-Wall Receptacle CA3500 1   Nov 2008 Indoor Link Link
This is a decent, but expensive solution for in-wall receptacles. One receptacle RF controlled, the other is hot.
Intermatic Appliance Module HA02C 1   Nov 2008 Indoor Link Link
Seems to work well
Intermatic Outdoor Module HA04C 1   Dec 2008 Outdoor Link Link Kozanator Easy to Install.
Merten switch, plug adapter, 2000 W 508519 6,2,7,1,5 EU   Indoor Link   Ap15e Works well.
Monster Central 1800W Appliance Module ML-LAS1000 1   Jan 2009 Indoor Link
guessed Easy to Install. I use this as a ZWave signal repeater. Appears to be a badge-engineering of Leviton VRP15-1LW
Wayne Dalton Appliance Module

HA-02L
(HA-02WD)

Dec 2011 Indooor Link DaveL17 Note: link is to HA-02WD manual.
Wayne Dalton Lamp Module HA-03WD Dec 2011 Indoor Link DaveL17 Not load sensing.


Thermostat Devices

Manufacturer Device Type Model no. Version Frequency Date Purchased Location (indoor/outdoor) Specs Product Review Added
By User 		Notes
Wayne Dalton Wall Stat WDTC-20  ??   Nov 2008 Indoor Link Link
Has 2 inclusion modes: 1) press and release the bind button and the STAT will be included as a thermostat and works with Vera, 2) press and hold the bind button and it will be added as a binary switch for compatibility with old, non-compliant remotes. If it's added in the wrong mode, remove it and re-add it. Works great simple to use!
HAI Wall Stat RC-80BZ  ??   Nov 2007 Indoor Link Link
Shows up as Standard Thermostat in Vera, Hold button feature not able to control by Vera at this time. Priced above 200.00. Has internal setback programs. Works great.
RCS Wall Stat TZ43  ??   Nov 2008 Indoor Link Link
Shows up as Standard Thermostat in Vera, much more feature rich the the WDTC-20 but comes with a hefty price tag ($214.95). Wish Vera could use all the features in this Thermostat! Note:You need to set the thermostat to show the temperature, on its display, in Celsius degree in order to be able to receive "Set Temp" commands from Vera. This is no longer required in firmwares above 1.0.862 (luup)
Schlage/Trane Wall Stat Trane  ??    ?? Indoor Link Link
It's the same thermostat as the RCS TZ43 and it has the same issue: it's accepting "Set Temp Point" commands only in the measurement unit that is displayed on its screen. Note:You need to set the thermostat to show the temperature, on its screen, in Celsius degree in order to be able to receive "Set Temp" commands from Vera. This is no longer required in firmwares above 1.0.862 (luup)
Intermatic InTouch CA8900
  Nov 2008 Indoor Link

Looks very similar to the Wayne Dalton WDTC-20 listed here. works great, simple to use
Danfoss Radiator thermostat RA PLUS-w
EU
Indoor Link Link Link [1]
See: Danfoss Thermostat for installation instructions
If the device cannot be configured at the final location, move the device closer to Vera and try again (this device might require a direct connection to Vera for configuration).
Radio Thermostat Wall Stat CT22
US
Indoor Link Link
Daniel

To include the thermostat into your network, you just have to install the USNAP module in the thermostat while Vera is in Include mode. You can watch a video about how to install it here

Note: There have been reports that the thermostat (mostly CT30) is causing trouble into the Z-Wave network, flooding it, not only with the Vera controller, but also with others.

Remotec Wall Stat ZTS-100
Indoor To include the thermostat into your network, hold the home button for 2 seconds until the display says 'noc', which means 'no connection', then press the Prog button and the readout will say 'Srh'. If it doesn't say 'noc' or if the radio icon is visible in the upper right corner, the thermostat is already included and must be removed/reset. To remove/reset the thermostat hold the home button for 2 seconds until the display says 'done', then press the Prog button.
Horstmann Wall Stat HRT4-ZW EU Indoor Link Link
Daniel After you include the thermostat in Vera's network, you will have to make some configuration changes in order for it to report the temperature change. See: HRT4-ZW for more information.


Sensors

Manufacturer Device Type Model no. Version Frequency Date Purchased Location (indoor/outdoor) Specs Product Review Added by User Notes
ACT Motion Sensor ZIR000 / ZIR010
EU (ZIR010) or US (ZIR000)
Indoor Link Link Link Link

Remove the cover, pair to Vera's dongle by using the push-button on the left of the circuit board. Vera must configure it to work, and it can only be configured within less of a minute (30 sec best) of inserting the batteries. With Vera's dongle removed, remove/reinsert the batteries, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page
Aeon Labs 3-in-1 sensor (light/humidity/temperature) MultiSensor
EU or US
Indoor/Outdoor Specs

Pair to Vera by using the push-button. Vera must configure it to work, and it can only be configured within 10 minutes of inserting the batteries.
Express Controls aka HomeSeer 3-in-1 sensor (light/temperature/motion) HSM100 / EZMotion
EU or US

Link

See ExpressControls3in1
If the motion sensor does not work right after inclusion and configuration, remove the batteries for a few seconds.
EverSpring/Hawking/Home Manageables Door/window sensor SM103 6,2,9,1,0 EU or US Apr 2009 Indoor Link Link   Ap15e Pair using the intrusion button. The sensor will accept configuration within a few minutes of the initial pairing, or of pressing the intrusion button on the back even after it's paired. Pair the device, or if it's already paired, press the intrusion button, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page. NOTE: There is some confusion about the orientation of the sensor. The main sensor body has a back (where the intrusion is), a front (where the logo and LED is), and the 2 other surfaces, one of which has a curved edge, and the other is flat. The magnet needs to go against the flat surface. And the flat surface on the magnet should be as close as possible to the flat surface on the sensor, lined up in the middle so the line which passes through the LED lines up with the sensor.

Note: In case the inclusion/exclusion fails you should remove/reinsert the batteries from the sensor and within a few seconds the sensor should be automatically detected.

EverSpring/Home Manageables Humidity + Temperature sensor HM-TS001

Jan 2010 (requires version 1.1.0 or greater) Indoor Link Link   micasaverde Pair or unpair the device by tapping the CF button 3 times very quickly. Once it's paired and shows up in the UI as a generic device, press the CF button 3 times again quickly to make it wakeup and get configured. Then it will correctly be identified as 3 devices (combo device + temperature + humidity).
Everspring Motion Detector SP103 6,2,9,1,0 EU or US Apr 2009 Indoor Link Link   Ap15e Works well
Fortrezz Water /Freeze WWA-001  ?????? US Apr 2009 Indoor Link Link
Zmistro Works great I would place a few in your house. Bathrooms, laundry , kitchen , basement. Great product!
Intermatic Motion Sensor CA-9000
US
Indoor Link
Aaron This device has limited functionality as a sensor. It can only be used to turn on and off a light directly by setting an association, which Vera supports. It does not fire events, so you cannot use it as an event on a scene.
Merten 4-gang radio transmitter, flush-mounted 506004 2,2,27,1,4 EU   Indoor Link   Ap15e Note: There is proprietary functionality here. Support will be added soon.

Quite complex device; partially supported by Vera; can be used as a window/door sensor (as of firmware 1.0.900) ...


Door Locks

Manufacturer Device Type Model no. Version Date Purchased Location (indoor/outdoor) Specs Product Review Added
By User 		Notes
Schlage Door lock and deadbolt BE369 (deadbolt)
Mid 2009 Indoor Link
LibraSun Read the instructions here: Schlage Lock
Kwikset Door lock and deadbolt Indoor Read instructions here:Kwikset Lock
Yale Deadbolt Real Living Indoor

Link

Link

Read instructions here: Yale Lock


Drapes/Blinds

Manufacturer Device Type Model no. Version Date Purchased Location (indoor/outdoor) Specs Product Review Added
By User 		Notes
Electronic Solutions Drape/Blind Motor Controller DBMZ V2+1
Indoor For 12-24VDC Motors Link Shady 2-Wire Motors
Electronic Solutions Drape/Blind Motor Controller ABMHZ V2+1
Indoor For 110-230VAC Motors Link Shady 4-Wire Motors
Lagotek / RSSceneAutomation Drape/Blind Motor Controller DC1-ZW

Indoor For 12-24VDC Motors Link Shady 2-Wire Motors
Lagotek / RSSceneAutomation Drape/Blind Motor Controller AC1-ZW

Indoor For 110-230VAC Motors Link Shady 4-Wire Motors


Relay controls

Manufacturer Device Type Model no. Version Date Purchased Location (indoor/outdoor) Specs Product Review Added
By User 		Notes
Intermatic Contactor control box CA3750
Nov 2007 Indoor/Outdoor Link

Multi-instance class supported for this device. Vera is able to control each of the 2 relays independently if desired. please note unit shows as three switches this is a bug with Intermatic not a real issue.You can check the box in devices to not show the second listing of the first relay in "Dasboard" You can control heavy loads like a water heater ,pool pump motor/s. great device


Window Coverings

Manufacturer Device Type Model no. Version Frequency Date Purchased Location (indoor/outdoor) Specs Product Review Added by User Notes
Merten Radio roller shutter push-button 5025xx, 5035xx, 5045xx 6,2,27,2,3 and 6,2,27,2,4 EU Apr 2009 Indoor Link   Ap15e Open/Close buttons work well, but slide bar does not work. GUI buttons do not work with Luup release 1.0.843 and 1.0.862 (fixed with Luup release 1.0.879).
Workaround: Use a Luup Scene with the following code:

local lul_arguments = {}

lul_arguments["newTargetValue"]="0"

lul_resultcode,lul_resultstring,lul_job,lul_returnarguments = luup.call_action("urn:upnp-org:serviceId:SwitchPower1","SetTarget",lul_arguments,6) Replace "6" with your device number, replace "0" with "1" for inverse action.

Duewi Radio roller shutter push-button 054368 6,2,51,1,0 EU Jun 2009 Indoor Link   Lutz Open/Close buttons work well, but slide bar does not work.

Some additional observations by Ap15e (Vera V1, firmware 1.0.979):
  • GUI button 'Stop' and corresponding UPnP service does not work.
  • GUI button 'Up' moves the shutter down, GUI button 'Down' moves the shutter up ...
  • After adjusting the running times even the slide bar seems to work!
  • I got a report from a user that the düwi device may fail due to interference from the shutter motor. In this case an additional filter is required (costs about 25 €/direction).
  • More information is available at Link


Cameras that work

See IP Cameras for a more comprehensive and up to date list

Manufacturer Device Type Model no. Version Date Purchased Location (indoor/outdoor) Path for JPEG image Product Review Notes
Linksys IP Camera WVC54GCA all 2009 Indoor img/snapshot.cgi
An inexpensive camera with moderate image quality. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address.
Linksys IP Camera WVC210 all 2009 Indoor img/snapshot.cgi
A more expensive camera with good image quality and pan/tilt ability. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address. Pan/tilt controls will not work with Vera.
Linksys IP Camera WVC80N all 2009 Indoor img/snapshot.cgi?size=2&quality=1
A more expensive camera with good image quality and wireless N. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address. Pan/tilt controls will not work with Vera.

Size can be (160 x 120 = 1,320 x 240 = 2,640 x 480 = 3) and Quality can be (Very High= 1,High= 2,Normal= 3,Low= 4,Very Low= 5)

iCamView IP Camera Server iCV-22, iCV-32 all 2009
 Indoor/Outdoor pda.cgi?user=admin&password=1234&page=image&cam=1

pda.cgi?user=admin&password=1234&page=image&cam=2
Feature-rich IP camera server, suports up to two compatible USB cameras, optional WiFi support, USB storage, USB hubs, motion; works with range of cameras, see icamview.co.uk. Excellent modular solution. They do ship to North America.
SmartHome.com.au IP Camera Z~Series Wireless Camera all 2009
 Indoor tmpfs/auto.jpg
Inexpensive IP security camera designed for the Australian and New Zealand Z-Wave users, but shipping world wide.
LevelOne IP Camera WCS-2030 all 2010 Indoor cgi-bin/video.jpg CNET review An inexpensive IP camera with good image quality. Can be connected wired or wirelessly. Most LevelOne cameras use the same path for the JPEG image, so most of their line (both low and high end) should be compatible. Video and audio also stream over RTSP, which can be customized through the camera's web interface.
Asante IP Camera Voyager I firmware 2.02 and above 2010 Indoor image.cgi
An inexpensive IP camera that is very feature rich, has good image quality, night vision capabilities, motion detection, two-way audio, video streaming over TCP, UDP, or HTTP, and other configurable features. In firmware version 2.02, Asante added the capability to retrieve an image via a URL (however, it is delayed by 3 seconds). Offers a full-featured web interface in IE using an ActiveX plug-in (limited capabilites in other browsers).


Alarm Panels

Manufacturer Model(s) Required module Plugin Notes
DSC IT-100 Link
Elk The M1EZ8 panel requires the ELK-M1EZ8MSI Main Serial Port Interface. Link You can use the ELK-M1XEP Ethernet Interface to connect the panels to Vera on the Ethernet port.
GE Security / Interlogix / Caddx NX-584 Link NetworX NX-8E already has a RS-232 interface, so it doesn't require the NX-584 module.
Honeywell / Ademco VISTA-50P, VISTA-128BP, VISTA-128BPT, VISTA-128BPE, VISTA-128FBP, VISTA-250BP, VISTA-250BPT, VISTA-250BPE and VISTA-250FBP VISTA-50P, VISTA-128BP, VISTA-128FBP, VISTA-250BP, and VISTA-250FBP panels require the 4100SM module. Link If your Vista panel is not on this list, look at the next row.
Honeywell / Ademco 10SE, 20SE, 10P, 15P, 20P, 50P, etc. AD2USB Link
Paradox
  • Digiplex DGP-848
  • EVO48
  • EVO192
PRT3 Integration Module Link
Visonic RS-232 Interface Module Link
Retrieved from "http://wiki.mios.com/index.php?title=Supported_Hardware&oldid=4201"
Personal tools