Leviton Vizia Remote
| Line 9: | Line 9: | ||
Setup -> Z-Wave Settings ->Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save. | Setup -> Z-Wave Settings ->Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save. | ||
| − | 2) After you check that the version is 2.78 and not 3.20, you will need to change the Vera unit to be secondary | + | 2) After you check that the version is 2.78 and not 3.20, you will need to change the Vera unit to be secondary. To do this bring the Leviton controller near the Vera unit, less than 5 feet and on the Vera unit go to: |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller' | Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller' | ||
| − | + | 3) Then, on the remote controller you must go to: | |
'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data' <br> | 'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data' <br> | ||
| Line 32: | Line 28: | ||
Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save | Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save | ||
| − | <div><div> 2) After you check that the version is 2.78 and not 3.20, you will need to change the Vera unit to be secondary | + | <div><div> 2) After you check that the version is 2.78 and not 3.20, you will need to change the Vera unit to be secondary.</div><div> To do this bring the Leviton controller near the Vera unit, less than 5 feet and on the Vera unit go to: </div> </div> |
| − | + | ||
| − | < | + | |
| − | + | ||
| − | + | ||
Z-Wave device -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller''''<br>''' | Z-Wave device -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller''''<br>''' | ||
Revision as of 15:45, 11 July 2012
To make Vera secondary to use the Leviton as primary you will need to follow these steps:
For UI5
1) First you will need to change the Z-Wave firmware to 2.78:
Setup -> Z-Wave Settings ->Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save.
2) After you check that the version is 2.78 and not 3.20, you will need to change the Vera unit to be secondary. To do this bring the Leviton controller near the Vera unit, less than 5 feet and on the Vera unit go to:
Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller'
3) Then, on the remote controller you must go to:
'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data'
When the Vera unit is secondary, you will need to go to:
Setup -> Z-Wave Settings -> Options -> uncheck the options 'By default Vera should automatically configure devices' and 'Use Vera routing instead of Z-Wave (requires 4.5)'.
For UI4
1) First you will need to change the Z-Wave firmware to 2.78:
Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save
Z-Wave device -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller'
4) Then, on the remote controller you must go to:
'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data'
When the Vera unit is secondary, you will need to go to:
Z-Wave device -> Options -> uncheck the options 'By default Vera should automatically configure devices' and 'Use Vera routing instead of Z-Wave (requires 4.5)'.
