Leviton Vizia Remote
| Line 1: | Line 1: | ||
To make Vera secondary to use the Leviton as primary you will need to follow these steps: | To make Vera secondary to use the Leviton as primary you will need to follow these steps: | ||
| − | + | <br> | |
| + | |||
| + | == For UI5<br> == | ||
1) First you will need to change the Z-Wave firmware to 2.78: | 1) First you will need to change the Z-Wave firmware to 2.78: | ||
| − | + | ||
| + | Setup -> Z-Wave Settings ->Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save. | ||
| + | |||
| + | 2) After you check that the version is 2.78 and not 3.20, you will need to change the _UNIT_NAME_ unit to be secondary, to do this go to: | ||
| + | |||
| + | Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Controller shift' | ||
| + | |||
| + | 3) Bring the Leviton controller near the _UNIT_NAME_ unit, less than 5 feet and on the _UNIT_NAME_ unit go to: | ||
| + | |||
| + | Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller' | ||
| + | |||
| + | 4) Then, on the remote controller you must go to: | ||
| + | |||
| + | 'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data' <br> | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | <div> | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | When the Vera unit is secondary, you will need to go to: | ||
| + | |||
| + | Setup -> Z-Wave Settings -> Options -> '''uncheck''' the options <span>'By default Vera should automatically configure devices' and '<span>Use Vera routing instead of Z-Wave (requires 4.5)</span>'.</span> | ||
| + | |||
| + | <span /><br> | ||
| + | |||
| + | |||
| + | </div> | ||
| + | |||
| + | |||
| + | == For UI4 == | ||
| + | 1) First you will need to change the Z-Wave firmware to 2.78: | ||
| + | |||
| + | |||
| + | |||
Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save | Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save | ||
| − | <div> | + | <div> |
| + | |||
| + | <div> 2) After you check that the version is 2.78 and not 3.20, you will need to change the _UNIT_NAME_ unit to be secondary, to do this go to:</div> | ||
| + | Z-Wave device -> Advanced -> click Go next to 'Controller shift' | ||
| + | </div> | ||
| + | 3) Bring the Leviton controller near the _UNIT_NAME_ unit, less than 5 feet and on the _UNIT_NAME_ unit go to: | ||
| + | |||
| + | Z-Wave device -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller''''<br>''' | ||
| + | |||
| + | |||
| + | |||
| + | 4) Then, on the remote controller you must go to: | ||
| + | |||
| + | 'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data' | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | <div><div> | ||
| + | |||
| + | |||
| + | When the Vera unit is secondary, you will need to go to: | ||
| + | |||
| + | Z-Wave device -> Options -> '''uncheck''' the options <span>'By default Vera should automatically configure devices' and '<span>Use Vera routing instead of Z-Wave (requires 4.5)</span>'.</span> | ||
| + | </div></div> | ||
Revision as of 10:27, 11 July 2012
To make Vera secondary to use the Leviton as primary you will need to follow these steps:
For UI5
1) First you will need to change the Z-Wave firmware to 2.78:
Setup -> Z-Wave Settings ->Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save.
2) After you check that the version is 2.78 and not 3.20, you will need to change the _UNIT_NAME_ unit to be secondary, to do this go to:
Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Controller shift'
3) Bring the Leviton controller near the _UNIT_NAME_ unit, less than 5 feet and on the _UNIT_NAME_ unit go to:
Setup -> Z-Wave Settings -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller'
4) Then, on the remote controller you must go to:
'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data'
When the Vera unit is secondary, you will need to go to:
Setup -> Z-Wave Settings -> Options -> uncheck the options 'By default Vera should automatically configure devices' and 'Use Vera routing instead of Z-Wave (requires 4.5)'.
<span />
For UI4
1) First you will need to change the Z-Wave firmware to 2.78:
Z-Wave device -> Options -> uncheck the option 'Use Z-Wave version 3.20 instead of 2.78' and Save
Z-Wave device -> Advanced -> click Go next to 'Controller shift'
3) Bring the Leviton controller near the _UNIT_NAME_ unit, less than 5 feet and on the _UNIT_NAME_ unit go to:
Z-Wave device -> Advanced -> click Go next to 'Copy Z-Wave network from a master controller'
4) Then, on the remote controller you must go to:
'Menu - System Setup - Advanced - Yes - Network - Primary utils - Send primary data'
When the Vera unit is secondary, you will need to go to:
Z-Wave device -> Options -> uncheck the options 'By default Vera should automatically configure devices' and 'Use Vera routing instead of Z-Wave (requires 4.5)'.
