Supported Hardware
From MiOS
(Difference between revisions)
(→Plug & Receptacle Devices) |
Micasaverde (Talk | contribs) (→Sensors) |
||
| Line 85: | Line 85: | ||
|| ACT || Motion Sensor || PIR000 / PIR010|| || || Indoor || || || Remove the cover, pair to Vera's dongle by using the push-button on the left of the circuit board. Vera must configure it to work, and it can only be configured within a few minutes of inserting the batteries. With Vera's dongle removed, remove/reinsert the batteries, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page | || ACT || Motion Sensor || PIR000 / PIR010|| || || Indoor || || || Remove the cover, pair to Vera's dongle by using the push-button on the left of the circuit board. Vera must configure it to work, and it can only be configured within a few minutes of inserting the batteries. With Vera's dongle removed, remove/reinsert the batteries, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page | ||
|- | |- | ||
| − | || Express Controls || 3-in-1 sensor || || || || || || || Pair using the blue button. The sensor will accept configuration within a few minutes of pressing the blue button, whether or not you are actually pairing or just pushing the button. So, with Vera's dongle removed, pair it or press the blue button if it's already paired, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page. This will show up as a device with 3 embedded devices (motion sensor, light sensor, thermometer) | + | || Express Controls || 3-in-1 sensor || || || || || || || Pair using the blue button. The sensor will accept configuration within a few minutes of pressing the blue button, whether or not you are actually pairing or just pushing the button. So, with Vera's dongle removed, pair it or press the blue button if it's already paired, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page. This will show up as a device with 3 embedded devices (motion sensor, light sensor, thermometer). Be sure the configure icon is green, indicating the sensor is configured. If not, press the blue button on the side of the sensor which causes the sensor to wake it up for a couple minutes and accept configuration settings. Then, within a couple minute, in Vera's Web UI, click the '+' button next to the sensor and click 'configure right now'. |
|- | |- | ||
|| EverSpring/Hawking/Home Managemeables || Door/window sensor || || || || || || || Pair using the intrusion button. The sensor will accept configuration within a few minutes of the initial pairing, or of pressing the intrusion button on the back even after it's paired. Pair the device, or if it's already paired, press the intrusion button, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page | || EverSpring/Hawking/Home Managemeables || Door/window sensor || || || || || || || Pair using the intrusion button. The sensor will accept configuration within a few minutes of the initial pairing, or of pressing the intrusion button on the back even after it's paired. Pair the device, or if it's already paired, press the intrusion button, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page | ||
Revision as of 14:11, 19 January 2009
This will have a list of supported hardware. For now, refer to the MiCasaVerde Shop
Contents |
Hardware Reported to Work
- We strongly encourage users to list any and all products they tested and installed.
- If a product works but you did not like it, please list it anyway. It may be the only product available to some users.
IMPORTANT! The devices listed here have been added by installers,technicians and users like yourself. Results may vary upon installations. MiCasaVerde does not guarantee operation and compatibility with your installation. The listed devices were found to work with their specific installation. Mixing different series and brands of equipment is not guaranteed in any way to work with other series and brands. It is very likely that users have not fully tested all features of the devices, so it is possible that a device listed here as compatible, will not prove compatible with your hardware. If you are editing this wiki DO NOT REMOVE a listed working device if it hasn't worked for you. Seek help to get the device to work under your individual circumstance. If you are adding to this wiki, please provide links to data for the device and add any tips you feel may benefit someone wanting to implement the device into an installation
Lighting Devices
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Added by User | Notes |
|---|---|---|---|---|---|---|---|---|---|
| Leviton | Dimmer Switch | VRM10-1LX | 1 | Nov 2008 | Indoor | Link | Link | mark-hc | This is a high quality dimmer geared towards high-end installations |
| Intermatic | 3-way Switch | HA18 | Dec 2008 | Indoor | Link | Kozanator | Affordable 3-way Switch | ||
| Intermatic | 3-way Dimmer Switch | HA20 | Nov 2008 | Indoor | Link | Link | Affordable 3-way 600W dimmer | ||
| ACT | 2-way Dimmer Switch | ZDW120 | Nov 2008 | Indoor | Link | Link | WSeverino | Works well, easy to install, LED is a very bright blue....can be programmed to be off when the light is off or on. | |
| ACT | 3-way Dimmer Switch | ZDW103 | Nov 2008 | Indoor | Link | Link | WSeverino | Works well, can be tricky to install due to the different combination of 3 way circuits, LED is a very bright blue....can be programmed to be off when the light is off or on. | |
| ACT | Companion Switch | AS101 | Nov 2008 | Indoor | Link | Link | WSeverino | Works well, can be tricky to install due to the different combination of 3 way circuits, The trick here is to install this device where the power comes in. | |
| Intermatic | Screw-in Module | HA05C | Nov 2008 | Outdoor | Link | Link | WSeverino | Easy install, easy to pair with Vera! |
Plug & Receptacle Devices
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Added by User | Notes |
|---|---|---|---|---|---|---|---|---|---|
| Intermatic | In-Wall Receptacle | CA3500 | 1 | Nov 2008 | Indoor | Link | Link | This is a decent, but expensive solution for in-wall receptacles | |
| Intermatic | Appliance Module | HA02C | 1 | Nov 2008 | Indoor | Link | Link | Seems to work well | |
| ACT | In-Wall Receptacle | ZRR150W | 2.2 | Nov 2008 | Indoor | Link | Link | Works like a champ! Easy to Install | |
| Intermatic | Outdoor Module | HA04C | 1 | Dec 2008 | Outdoor | Link | Link | Kozanator | Easy to Install. |
Thermostat Devices
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Notes |
|---|---|---|---|---|---|---|---|---|
| Wayne Dalton | Wall Stat | WDTC-20 | ?? | Nov 2008 | Indoor | Link | Link | Shows up as Standard Thermostat, shows room temp, as well as controlling HVAC |
| RCS | Wall Stat | TZ43 | ?? | Nov 2008 | Indoor | Link | Link | Shows up as Standard Thermostat in Vera, much more feature rich the the WDTC-20 but comes with a hefty price tag ($214.95). Wish Vera could use all the features in this Thermostat!
|
Cameras
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Notes |
|---|---|---|---|---|---|---|---|---|
| Panasonic | IP Camera | BL-C131/BL-C30 | all | Indoor | The Panasonic IP cameras work well with Vera. However, for unknown reasons, the Panasonic camera will not get an IP address on your LAN until you run the Windows software supplied with it. You do not need to install the software; just insert the CD and tell the camera to get an IP address automatically (DHCP). If you buy the camera from the Mi Casa Verde web shop we do this before we ship it so the camera will work out of the box. Mac/Linux users who buy the camera elsewhere will need a Windows PC to 'activate' the camera. Set the default username/password on the camera to: dceadmin and dcepass for Vera to detect the camera automatically, or, if you use your own username/password, add the camera to Vera manually and provide Vera your username/password to access the camera. |
Sensors
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Notes |
|---|---|---|---|---|---|---|---|---|
| ACT | Motion Sensor | PIR000 / PIR010 | Indoor | Remove the cover, pair to Vera's dongle by using the push-button on the left of the circuit board. Vera must configure it to work, and it can only be configured within a few minutes of inserting the batteries. With Vera's dongle removed, remove/reinsert the batteries, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page | ||||
| Express Controls | 3-in-1 sensor | Pair using the blue button. The sensor will accept configuration within a few minutes of pressing the blue button, whether or not you are actually pairing or just pushing the button. So, with Vera's dongle removed, pair it or press the blue button if it's already paired, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page. This will show up as a device with 3 embedded devices (motion sensor, light sensor, thermometer). Be sure the configure icon is green, indicating the sensor is configured. If not, press the blue button on the side of the sensor which causes the sensor to wake it up for a couple minutes and accept configuration settings. Then, within a couple minute, in Vera's Web UI, click the '+' button next to the sensor and click 'configure right now'. | ||||||
| EverSpring/Hawking/Home Managemeables | Door/window sensor | Pair using the intrusion button. The sensor will accept configuration within a few minutes of the initial pairing, or of pressing the intrusion button on the back even after it's paired. Pair the device, or if it's already paired, press the intrusion button, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page |
Controller/Gateway
| Manufacturer | Device Type | Model no. | Version | Date Purchased | Location (indoor/outdoor) | Specs | Product Review | Notes |
|---|---|---|---|---|---|---|---|---|
| Wayne Dalton | Gateway | WDHA-12R | ?? | Nov 2008 | Indoor | Link | Link | Shows as Z-Wave controller, a pain to sync with Homelink car remote, able to associate with devices, but not through Vera yet. Can now turn on/off All Z-wave devices from car. This gateway is required for the 3-button remote sold by them. Translates commands to Z-Wave Scenes. |
| Cooper Wiring Devices | Handheld Controller | RFHDCSG | 1.13 | Nov 2008 | Indoor | Link | Link | Works well with Vera. Can transfer devices from Vera to the handheld but doesn't transfer device names. Also very expensive. |
| Leviton | 1 Scene Controller | LEVRZCZ1-1LX | Unknown | Nov 2008 | Indoor | Link | Link | Have had problems working with Vera. Finally, got it to pair with Vera but have not figured out the associations. |
