Luup UPnP Variables and Actions - Revision history

Mcvflorin: /* EnergyMetering1 */

2018-03-06T09:16:51Z

‎EnergyMetering1

2018-01-26T12:15:02Z

‎HaDevice1

2017-12-12T08:53:11Z

2017-12-12T08:51:49Z

2017-10-19T08:28:37Z

‎HaDevice1

2017-08-30T09:13:35Z

‎DoorLock1

2017-08-22T09:02:30Z

‎TemperatureSetpoint1

2017-08-01T12:07:09Z

‎ZWaveDevice1

2017-04-25T08:47:23Z

‎ZWaveDevice1

2017-04-24T09:09:49Z

‎TemperatureSetpoint1

@@ Line 2,054: / Line 2,054: @@
 | style="border: 1px solid #000" | See <tt>Watts</tt>.
 '''Note:''' For thermostats, <tt>UserSuppliedWattage</tt> consists of 3 numbers separated by commas. The default is 1500,1500,300. The first number is how many watts are used when the thermostat is in 'heat' mode; the second is how many watts are used when the thermostat is in 'cool' mode; and the third number is for the 'fan only' mode.
 |-
 | style="border: 1px solid #000" | KWH
-| style="border: 1px solid #000" | ui4
+| style="border: 1px solid #000" | float
-| style="border: 1px solid #000;  text-align: center" | -
+| style="border: 1px solid #000" | If the device can report its energy consumption, this is the value reported by the device.
 |-
 | style="border: 1px solid #000" | Log
@@ Line 2,085: / Line 2,088: @@
 | style="border: 1px solid #000" rowspan="1" | -
 |}
 == IrTransmitter1 ==

@@ Line 228: / Line 228: @@
 |-
 | style="border: 1px solid #000" | CommFailure
-| style="border: 1px solid #000" | boolean
+| style="border: 1px solid #000" | i1
-| style="border: 1px solid #000" | This is set to ''1'' if we've lost communication with the device.
+| style="border: 1px solid #000" | Contains the communication status with the device:
 |-
 | style="border: 1px solid #000" | Configured

← Older revision		Revision as of 08:53, 12 December 2017
Line 1:		Line 1:
	[[Category:Development]]		[[Category:Development]]
−
	This is a list of all the UPnP actions and variables used by MiOS.		This is a list of all the UPnP actions and variables used by MiOS.

← Older revision		Revision as of 08:51, 12 December 2017
Line 1:		Line 1:
		+	[[Category:Development]]
		+
	This is a list of all the UPnP actions and variables used by MiOS.		This is a list of all the UPnP actions and variables used by MiOS.

@@ Line 231: / Line 231: @@
 |-
 | style="border: 1px solid #000" | Configured
-| style="border: 1px solid #000" | boolean
+| style="border: 1px solid #000" | i1
 | style="border: 1px solid #000" | The configuration state of the device:
 *-3 = Configuration failed
@@ Line 390: / Line 390: @@
 | style="border: 1px solid #000" rowspan="1" | Toggle the state of the device (e.g. if the device it's Off, turns it On). The device must have a binary state (On/Off, Locked/Unlocked, etc.).
 |}
 == ZWaveDevice1 ==

@@ Line 1,473: / Line 1,473: @@
 | style="border: 1px solid #000" | ui1
 | style="border: 1px solid #000" | The minimum and maximum number of digits of the PIN code.
 |-
 | style="border: 1px solid #000" | sl_UserCode
@@ Line 1,673: / Line 1,685: @@
 | style="border: 1px solid #000" rowspan="1" | Removes the PIN code from slot <tt>UserCode</tt>.
 |}
 == HVAC_UserOperatingMode1 ==

@@ Line 1,854: / Line 1,854: @@
 | style="border: 1px solid #000" | Reject setpoint change commands whose setpoint is outside the specified range.
 Format:
 <code>C<sub>min</sub>,C<sub>max</sub>/F<sub>min</sub>,F<sub>max</sub></code>
 The range limits are inclusive, meaning the new setpoint must be >= X<sub>min</sub> and <= X<sub>max</sub>.
-Example: <code>-15,99/5,210</code>
+Example: <code>14,34/58,92;16,44/60,112;-1,32/30,90</code>
 |}

@@ Line 714: / Line 714: @@
 *<tt>NotificationType</tt>&nbsp;: type1,type2-type3,!type4, XX (don't care)
 *<tt>Event</tt>&nbsp;: 00,01,03-5A,!04,!FF, XX (don't care)
-*<tt>AlarmCode</tt>&nbsp;: SMOKE, CO, TAMPER_ALARM, etc.
+*<tt>AlarmCode</tt>&nbsp;: SMOKE, CO, TAMPER_ALARM, etc. Leave empty if you don't want to set an alarm code.
 *<tt>TripValue</tt>&nbsp;: 0 = Untrip, 1 = Trip, C = don't update the Tripped variable (only the Alarm Code), X = Ignore

@@ Line 743: / Line 743: @@
 That means: ignore CC 26 commands 03 and 05, all commands from CC 71, and CC 20 command 03.
 |}
 == ZWaveNetwork1 ==

← Older revision		Revision as of 09:09, 24 April 2017
Line 1,838:		Line 1,838:

	The range limits are inclusive, meaning the new setpoint must be >= X<sub>min</sub> and <= X<sub>max</sub>.		The range limits are inclusive, meaning the new setpoint must be >= X<sub>min</sub> and <= X<sub>max</sub>.
		+
		+	Example: <code>-15,99/5,210</code>
	\|}		\|}