HRT4-ZW - Revision history

A-lurker at 02:59, 15 June 2013

2013-06-15T02:59:24Z

Mcvdaniel at 14:00, 8 February 2012

2012-02-08T14:00:48Z

Mcvdaniel at 19:50, 1 February 2012

2012-02-01T19:50:07Z

Mcvdaniel at 19:20, 1 February 2012

2012-02-01T19:20:47Z

Mcvdaniel at 19:16, 1 February 2012

2012-02-01T19:16:24Z

Mcvdaniel at 19:02, 1 February 2012

2012-02-01T19:02:14Z

Mcvdaniel at 17:57, 1 February 2012

2012-02-01T17:57:56Z

Mcvdaniel at 16:00, 1 February 2012

2012-02-01T16:00:14Z

Mcvdaniel at 15:52, 1 February 2012

2012-02-01T15:52:04Z

Mcvdaniel: Created page with "Horstmann HRT4-ZW THERMOSTAT The user manual can be found [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHR..."

2011-11-10T14:41:21Z

Created page with "Horstmann HRT4-ZW THERMOSTAT The user manual can be found [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHR..."

New page

Horstmann HRT4-ZW THERMOSTAT

The user manual can be found [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHRT4-ZWweb.pdf&sa=D&sntz=1&usg=AFQjCNEfT2dDrFO2lqyECfxk-PEX2QUyhw here] and the Z-Wave information [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHRT4B-ZWManual.pdf&sa=D&sntz=1&usg=AFQjCNETHBMTFeuzlnT9mGMNswjSQCaxAQ here].

After you include the HRT4-ZW thermostat in Vera, you will have to change some configuration settings in order to make it work properly in the network and report the temperature to Vera. By default HRT4 is set to not do this automatically (see configuration parameter 1 at the bottom of this page) so you have to add this parameter yourself and insert a value higher than 128. To add a new configuration parameter, you have to click on the little wrench on the Dashboard, go to Device Options and click on ‘Add configuration settings’, then fill in the values for Parameter 1 as below:

[[Image:Add configuration settings.png]]

If you also want to make the thermostat wake up more frequently, you can specify a lower value for the Wakeup interval by clicking on the little wrench, go to Settings and edit the ‘Wakeup interval’ field as shown in the picture below. By default this value is set to 1800 seconds, but you can set it to a minimal value of 256 seconds. This is the shortest wakeup time interval that we know about for this sensor.

[[Image:Wakeup-interval.png]]

<br>

Configuration Command Class (V1)

The unit supports 3 single byte configurations for the temperature sensor functionality of the unit in the range 1 – 3 respectively.

Configuration Parameter Number 1:

0–127 disables temperature sensor, 128-255 enables temperature sensor. Default = 0.

Configuration Parameter Number 2:

0-127 = Celsius, 128-255 = Fahrenheit. Default = 0.

Configuration Parameter Number 3:

1 – 100 = Delta T in steps of 0.1 degree. Default = 10 (1.0).

← Older revision		Revision as of 02:59, 15 June 2013
Line 1:		Line 1:
		+	[[Category:Hardware]]
	= Horstmann HRT4-ZW THERMOSTAT =		= Horstmann HRT4-ZW THERMOSTAT =

@@ Line 3: / Line 3: @@
 The user manual can be found [http://www.horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4-ZWweb.pdf here] and the Z-Wave information [http://www.horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4B-ZWManual.pdf here].
-== Configuration  ==
+== Configuration<br> ==
 After you include the HRT4-ZW thermostat in Vera, you will have to change some configuration settings in order to make it work properly in the network and report the temperature to Vera. By default HRT4 is set to not do this automatically (see configuration parameter 1 below) so you have to add this parameter yourself and insert a value between 128 - 255. To add a new configuration parameter, you have to click on the little wrench on the Dashboard, go to Device Options and click on ‘Add configuration settings’, then fill in the values for Parameter 1 as below in the pictures.
@@ Line 18: / Line 18: @@
 <br>
-=== Wakeup time interval ===
+=== Wakeup time interval  ===
 If you also want to make the thermostat wake up more frequently, you can specify a lower value for the Wakeup interval by clicking on the little wrench, go to Settings and edit the ‘Wakeup interval’ field as shown in the picture below. By default this value is set to 1800 seconds, but you can set it to a minimal value of 256 seconds. This is the shortest wakeup time interval that we know about for this sensor.
@@ Line 57: / Line 57: @@
 == Association with ASR-ZW Receiver<br>  ==
-To make the HRT4-ZW work together with the ASR-ZW Receiver (they usually come in the same package) you have to include both of them in Veras Z-Wave network, then set up associations by clicking on the little wrench key on the HRT4-ZW and go to '''Device Options'''. In the '''Associations''' section you have to type in the '''Group ID '''number 1, then click on '''Set''', '''Save''' the changes and make sure to wake up the thermostat in order for it to receive the configuration changes. After that the devices should work together, but the status of the ASR-ZW Receiver will be updated only when Vera automatically polls it, or when you manually poll it. The device itself is&nbsp;
+To make the HRT4-ZW work together with the ASR-ZW Receiver (they usually come in the same package) you have to include both of them in Veras Z-Wave network, then set up associations by clicking on the little wrench key on the HRT4-ZW and go to '''Device Options'''. In the '''Associations''' section you have to type in the '''Group ID '''number 1, then click on '''Set''', '''Save''' the changes and make sure to wake up the thermostat in order for it to receive the configuration changes. After that the devices should work together, but the status of the ASR-ZW Receiver will be updated only when Vera automatically polls it, or when you manually poll it. The device itself is not sending the status change automatically.

@@ Line 18: / Line 18: @@
 <br>
-<br>
+=== Wakeup time interval ===
 If you also want to make the thermostat wake up more frequently, you can specify a lower value for the Wakeup interval by clicking on the little wrench, go to Settings and edit the ‘Wakeup interval’ field as shown in the picture below. By default this value is set to 1800 seconds, but you can set it to a minimal value of 256 seconds. This is the shortest wakeup time interval that we know about for this sensor.
-[[Image:Wakeup-interval.png|500x423px]]
+{| width="80%" border="0" cellpadding="1" cellspacing="1" align="center"
 <br>
@@ Line 48: / Line 57: @@
 == Association with ASR-ZW Receiver<br>  ==
-To make the HRT4-ZW work together with the ASR-ZW Receiver (they usually come in the same package) you have to include both of them in Veras Z-Wave network, then set up associations by clicking on the little wrench key on the HRT4-ZW and go to '''Device Options'''. In the '''Associations''' section you have to type in the '''Group ID '''number 1, then click on '''Set''', '''Save''' the changes and make sure to wake up the thermostat in order for it to receive the configuration changes.
+To make the HRT4-ZW work together with the ASR-ZW Receiver (they usually come in the same package) you have to include both of them in Veras Z-Wave network, then set up associations by clicking on the little wrench key on the HRT4-ZW and go to '''Device Options'''. In the '''Associations''' section you have to type in the '''Group ID '''number 1, then click on '''Set''', '''Save''' the changes and make sure to wake up the thermostat in order for it to receive the configuration changes. After that the devices should work together, but the status of the ASR-ZW Receiver will be updated only when Vera automatically polls it, or when you manually poll it. The device itself is&nbsp;

@@ Line 12: / Line 12: @@
 | '''UI5'''
 |-
-| [[Image:Add configuration settings.png|Add configuration settings.png]]
+| [[Image:Add configuration settings.png|500x423px|Add configuration settings.png]]
-| [[Image:Horstmann HRT4 UI5-parameters.png|Horstmann HRT4 UI5-parameters.png]]
+| [[Image:Horstmann HRT4 UI5-parameters.png|500x423px|Horstmann HRT4 UI5-parameters.png]]
 |}
@@ Line 22: / Line 22: @@
 If you also want to make the thermostat wake up more frequently, you can specify a lower value for the Wakeup interval by clicking on the little wrench, go to Settings and edit the ‘Wakeup interval’ field as shown in the picture below. By default this value is set to 1800 seconds, but you can set it to a minimal value of 256 seconds. This is the shortest wakeup time interval that we know about for this sensor.
-[[Image:Wakeup-interval.png]]
+[[Image:Wakeup-interval.png|500x423px]]
 <br>

@@ Line 12: / Line 12: @@
 | '''UI5'''
 |-
-| [[Image:Add configuration settings.png|600x423px|Add configuration settings.png]]
+| [[Image:Add configuration settings.png|Add configuration settings.png]]
-| [[Image:Horstmann HRT4 UI5-parameters.png|600x423px|Horstmann HRT4 UI5-parameters.png]]
+| [[Image:Horstmann HRT4 UI5-parameters.png|Horstmann HRT4 UI5-parameters.png]]
 |}

@@ Line 5: / Line 5: @@
 == Configuration  ==
-After you include the HRT4-ZW thermostat in Vera, you will have to change some configuration settings in order to make it work properly in the network and report the temperature to Vera. By default HRT4 is set to not do this automatically (see configuration parameter 1 at the bottom of this page) so you have to add this parameter yourself and insert a value higher than 128. To add a new configuration parameter, you have to click on the little wrench on the Dashboard, go to Device Options and click on ‘Add configuration settings’, then fill in the values for Parameter 1 as below in the pictures.
+After you include the HRT4-ZW thermostat in Vera, you will have to change some configuration settings in order to make it work properly in the network and report the temperature to Vera. By default HRT4 is set to not do this automatically (see configuration parameter 1 below) so you have to add this parameter yourself and insert a value between 128 - 255. To add a new configuration parameter, you have to click on the little wrench on the Dashboard, go to Device Options and click on ‘Add configuration settings’, then fill in the values for Parameter 1 as below in the pictures.
 {| width="80%" border="0" align="center" cellpadding="1" cellspacing="1"

@@ Line 1: / Line 1: @@
-Horstmann HRT4-ZW THERMOSTAT
+= Horstmann HRT4-ZW THERMOSTAT  =
-The user manual can be found [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHRT4-ZWweb.pdf&sa=D&sntz=1&usg=AFQjCNEfT2dDrFO2lqyECfxk-PEX2QUyhw here] and the Z-Wave information [http://www.google.com/url?q=http%3A%2F%2Fwww.horstmann.co.uk%2Fdownloads%2FElectronicDocuments%2FCentral-Heating%2FHRT4B-ZWManual.pdf&sa=D&sntz=1&usg=AFQjCNETHBMTFeuzlnT9mGMNswjSQCaxAQ here].
+The user manual can be found [http://www.horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4-ZWweb.pdf here] and the Z-Wave information [http://www.horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4B-ZWManual.pdf here].
 After you include the HRT4-ZW thermostat in Vera, you will have to change some configuration settings in order to make it work properly in the network and report the temperature to Vera. By default HRT4 is set to not do this automatically (see configuration parameter 1 at the bottom of this page) so you have to add this parameter yourself and insert a value higher than 128. To add a new configuration parameter, you have to click on the little wrench on the Dashboard, go to Device Options and click on ‘Add configuration settings’, then fill in the values for Parameter 1 as below:
-[[Image:Add configuration settings.png]]
+{| width="80%" border="0" align="center" cellpadding="1" cellspacing="1"
 If you also want to make the thermostat wake up more frequently, you can specify a lower value for the Wakeup interval by clicking on the little wrench, go to Settings and edit the ‘Wakeup interval’ field as shown in the picture below. By default this value is set to 1800 seconds, but you can set it to a minimal value of 256 seconds. This is the shortest wakeup time interval that we know about for this sensor.
@@ Line 12: / Line 25: @@
 <br>
 Configuration Command Class (V1)
@@ Line 27: / Line 42: @@
 Configuration Parameter Number 3:
 – 100 = Delta T in steps of 0.1 degree. Default = 10 (1.0).