GE LED Settings - Revision history

Knewmania: Minor edits to correct process

2013-05-19T01:53:00Z

Minor edits to correct process

Knewmania: Added instructions to disable LED at all times

2013-05-17T19:10:45Z

Added instructions to disable LED at all times

Knewmania at 06:33, 21 February 2013

2013-02-21T06:33:23Z

Knewmania: Initial Creation

2013-02-21T06:26:09Z

Initial Creation

New page

== '''HOWTO Control LED Settings of GE Switch/Outlets''' ==

== Prerequisites ==

*Vera hardware
*GE Switch / Outlet
*UI5 firmware

== Introduction ==

This is a short manual on how to control the LED Settings of GE Switch/Outlets.

== LED On when Switch/Outlet is On ==

   1. Go to Vera's Dashboard (Open your Web browser and type the IP address of your Vera, or connect through mios.com.)

   2. In the UI, Find the Switch/Outlet you want to modify and click the Wrench icon.

   3. At the Device Settings screen, click the Device Options Tab.

   4. At the Device Options screen, under Configuration Settings enter the following values:
<pre>'3' in the Variable field

'1 byte hex' from the Data Size drop down

'1' in the Desired Value field</pre>
   5. Click the "Add Configuration Settings" Button.

   6. Close the Device Settings screen by clicking the X.

   7. Click the red "Save" button at the top of the UI.

== LED On when Switch/Outlet is Off (Default Setting) ==

   1. Go to Vera's Dashboard (Open your Web browser and type the IP address of your Vera, or connect through mios.com.)

   2. In the UI, Find the Switch/Outlet you want to modify and click the Wrench icon.

   3. At the Device Settings screen, click the Device Options Tab.

   4. At the Device Options screen, under Configuration Settings enter the following values:
<pre>'3' in the Variable field

'1 byte hex' from the Data Size drop down

'0' in the Desired Value field
</pre>
   5. Click the "Add Configuration Settings" Button.

   6. Close the Device Settings screen by clicking the X.

   7. Click the red "Save" button at the top of the UI.

<br>

[[Category:User_Instructions]] [[Category:How_To]]

@@ Line 19: / Line 19: @@
 &nbsp; &nbsp;3. At the Device Settings screen, click the Device Options Tab.
-&nbsp; &nbsp;4. At the Device Options screen, under Configuration Settings enter the following values:
+&nbsp; &nbsp;4. At the Device Options screen, click Add Configuration Setting.
 <pre>'3' in the Variable field
@@ Line 25: / Line 27: @@
 '1' in the Desired Value field</pre>
 &nbsp; &nbsp;6. Close the Device Settings screen by clicking the X.
@@ Line 39: / Line 39: @@
 &nbsp; &nbsp;3. At the Device Settings screen, click the Device Options Tab.
-&nbsp; &nbsp;4. At the Device Options screen, under Configuration Settings enter the following values:
+&nbsp; &nbsp;4. At the Device Options screen, click Add Configuration Setting.
 <pre>'3' in the Variable field
@@ Line 46: / Line 48: @@
 '0' in the Desired Value field
 </pre>
 &nbsp; &nbsp;6. Close the Device Settings screen by clicking the X.
@@ Line 60: / Line 60: @@
 &nbsp; &nbsp;3. At the Device Settings screen, click the Device Options Tab.
-&nbsp; &nbsp;4. At the Device Options screen, under Configuration Settings enter the following values:
+&nbsp; &nbsp;4. At the Device Options screen, click Add Configuration Setting.
 <pre>'3' in the Variable field
@@ Line 67: / Line 69: @@
 '2' in the Desired Value field
 </pre>
 &nbsp; &nbsp;6. Close the Device Settings screen by clicking the X.

@@ Line 52: / Line 52: @@
 &nbsp; &nbsp;7. Click the red "Save" button at the top of the UI.
-<br>
+== References  ==
 [[Category:User_Instructions]] [[Category:How_To]]

← Older revision		Revision as of 19:10, 17 May 2013
Line 51:		Line 51:

	7. Click the red "Save" button at the top of the UI.		7. Click the red "Save" button at the top of the UI.
		+
		+	== LED Off Always ==
		+
		+	1. Go to Vera's Dashboard (Open your Web browser and type the IP address of your Vera, or connect through mios.com.)
		+
		+	2. In the UI, Find the Switch/Outlet you want to modify and click the Wrench icon.
		+
		+	3. At the Device Settings screen, click the Device Options Tab.
		+
		+	4. At the Device Options screen, under Configuration Settings enter the following values:
		+	<pre>'3' in the Variable field
		+
		+	'1 byte hex' from the Data Size drop down
		+
		+	'2' in the Desired Value field
		+	</pre>
		+	5. Click the "Add Configuration Settings" Button.
		+
		+	6. Close the Device Settings screen by clicking the X.
		+
		+	7. Click the red "Save" button at the top of the UI.
		+
		+	<br>

	== References ==		== References ==