Aeon HomeEnergyMonitor - Revision history

George at 12:37, 10 November 2015

2015-11-10T12:37:12Z

George at 12:30, 10 November 2015

2015-11-10T12:30:11Z

Mcvdaniel at 10:59, 3 July 2012

2012-07-03T10:59:46Z

Mcvdennis at 10:57, 3 July 2012

2012-07-03T10:57:45Z

Mcvdennis at 10:52, 3 July 2012

2012-07-03T10:52:29Z

Mcvdennis at 10:47, 3 July 2012

2012-07-03T10:47:50Z

Mcvdennis at 10:43, 3 July 2012

2012-07-03T10:43:54Z

Mcv.adi at 14:26, 11 June 2012

2012-06-11T14:26:11Z

George at 17:50, 8 May 2012

2012-05-08T17:50:48Z

Mcv.adi at 17:49, 8 May 2012

2012-05-08T17:49:11Z

@@ Line 27: / Line 27: @@
 = <span dir="auto">Aeotec HomeEnergyMonitor 2nd edition</span><br/> =
-== <span dir="auto"></span>Configuring the Aeotec HEM 2nd edition<br/> ==
+<span dir="auto">The Aeotec Home Energy Monitor can be found in multiple variations on the market with one, two or three measuring clamps. It's always a good practice to update the software to the latest version by using the tool from the manuafcturers [http://aeotec.com/z-wave-home-energy-measure/1262-hem-firmware.html support page.]</span>
-The Aeotec Home Energy Monitor can be found in multiple variations on the market with one, two or three measuring clamps. It's always a good practice to update the software to the latest version by using the tool from the manuafcturers [http://aeotec.com/z-wave-home-energy-measure/1262-hem-firmware.html support page.]
+== Configuring the Aeotec HEM 2nd edition<br/> ==
 Once the HEM will be paired with your controller it will display either two, three or four devices on the Vera interface. One will be the master device, and one child device for each clamp connected to the HEM. Below we'll check the configuration settings for the two and three clamp versions of the Aeotec HEM.
-The configuration settings are done on the configuration panel of the parent device under the Device Options page. Here you'll need to adjust the following configuration parameters :
+The configuration settings are done on the configuration panel of the parent device under the Device Options page. Here you'll need to adjust the following configuration parameters&nbsp;:
 *for the two clamp edition:

@@ Line 1: / Line 1: @@
-If you have version 3.58 or later of the HEM firmware (unrelated to Vera's firmware), it supports the ability to report in real-time whenever there is a change in the energy consumption.&nbsp; It generates a report for Vera whenever there is a change.
+= <span dir="auto">Aeon HomeEnergyMonitor First Edition</span><br/> =
-For versions 3.57 and lower, the only way to get real time energy reporting was to have the HEM send Vera reports constantly, whether or not there was a change.&nbsp; This required powering the HEM with USB power.&nbsp; So we recommend using the USB port on the HEM to upgrade to firmware 3.58 or newer, as per the instructions on aeon-labs.com
+If you have version 3.58 or later of the HEM firmware (unrelated to Vera's firmware), it supports the ability to report in real-time whenever there is a change in the energy consumption.&nbsp; It generates a report for Vera whenever there is a change.
 There have been reported issues with HEM firmware less than 3.61. The latest that we know about is 3.67 and you can download it below. Please make sure to choose the right frequency for your own device.
 US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]
-AU version - 200 A: [http://wiki.micasaverde.com/images/4/45/Home_Energy_Meter_V3_67_AU_200A.zip HEM367]
+The configuration settings are done on the configuration panel of the parent device under the Device Options page. Here you'll need to adjust the following configuration parameters :
-EU version - 60 A&nbsp;:&nbsp; [http://wiki.micasaverde.com/images/3/37/Home_Energy_Meter_V3_67_EU_60A.zip HEM367]
+*for the two clamp edition:
-EU version - 100 A: [http://wiki.micasaverde.com/images/2/2a/Home_Energy_Meter_V3_67_EU_100A.zip HEM367]
+Parameter 101 [4 byte dec]: 6927 (report kwh and watt on clamp 1 2 and total readings)
-EU version - 200 A: [http://wiki.micasaverde.com/images/5/5e/Home_Energy_Meter_V3_67_EU_200A.zip HEM367]
+Parameter 111 [4 byte dec]: 240 (report every 240 seconds)
-== Inclusion  ==
+Parameter 102 and 103 [4 byte dec] set to 0<br/><br/>If any of the parameters are missing you can add them by pressing "Add configuration settings" button.
-When including the HEM to the Vera unit you should have the HEM&nbsp;powered with the <span style="color: rgb(255, 0, 0);">USB AC adapter</span>.
+*for the three clamp edition:
-== Note  ==
+Parameter 101 [4 byte dec]: 16143 (3 clamps to report kwh and watt)
-You need to have it plugged in through the <span style="color: rgb(255, 0, 0);">USB AC adapter</span> for it to report the KWH accurately, because when it is battery operated it sleeps most of the time and it cannot accurately track KWH.&nbsp;
+Parameter 111 [4 byte dec]: 240 (report every 240 seconds)
-[[Category:User_Instructions]] [[Category:Hardware]]
+Parameter 102 and 103 [4 byte dec] set to 0<br/><br/>If some of the parameters are missing one can add them by pressing "Add configuration settings" button.

@@ Line 3: / Line 3: @@
 For versions 3.57 and lower, the only way to get real time energy reporting was to have the HEM send Vera reports constantly, whether or not there was a change.&nbsp; This required powering the HEM with USB power.&nbsp; So we recommend using the USB port on the HEM to upgrade to firmware 3.58 or newer, as per the instructions on aeon-labs.com
-There have been reported issues with HEM firmware less than 3.61. If you don't have 3.61, download these files:
+There have been reported issues with HEM firmware less than 3.61. The latest that we know about is 3.67 and you can download it below. Please make sure to choose the right frequency for your own device.
 US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]

@@ Line 4: / Line 4: @@
 There have been reported issues with HEM firmware less than 3.61. If you don't have 3.61, download these files:
 US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]
 AU version - 200 A: [http://wiki.micasaverde.com/images/4/45/Home_Energy_Meter_V3_67_AU_200A.zip HEM367]
-EU version - 60 A :&nbsp; [http://wiki.micasaverde.com/images/3/37/Home_Energy_Meter_V3_67_EU_60A.zip HEM367]
+EU version - 60 A&nbsp;:&nbsp; [http://wiki.micasaverde.com/images/3/37/Home_Energy_Meter_V3_67_EU_60A.zip HEM367]
 EU version - 100 A: [http://wiki.micasaverde.com/images/2/2a/Home_Energy_Meter_V3_67_EU_100A.zip HEM367]
 EU version - 200 A: [http://wiki.micasaverde.com/images/5/5e/Home_Energy_Meter_V3_67_EU_200A.zip HEM367]
 == Inclusion  ==

← Older revision		Revision as of 10:52, 3 July 2012
Line 8:		Line 8:

	US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]		US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]
		+
		+	AU version - 200 A: [http://wiki.micasaverde.com/images/4/45/Home_Energy_Meter_V3_67_AU_200A.zip HEM367]
		+
		+	EU version - 60 A :  [http://wiki.micasaverde.com/images/3/37/Home_Energy_Meter_V3_67_EU_60A.zip HEM367]
		+
		+	EU version - 100 A: [http://wiki.micasaverde.com/images/2/2a/Home_Energy_Meter_V3_67_EU_100A.zip HEM367]
		+
		+	EU version - 200 A: [http://wiki.micasaverde.com/images/5/5e/Home_Energy_Meter_V3_67_EU_200A.zip HEM367]

	== Inclusion ==		== Inclusion ==

@@ Line 7: / Line 7: @@
 US version: [http://wiki.micasaverde.com/images/0/0c/HEM361.zip HEM361]
-US version: [http://wiki.micasaverde.com/index.php/File:Home_Energy_Meter_V3_67_US.zip HEM367]
+US version: [http://wiki.micasaverde.com/images/f/f6/Home_Energy_Meter_V3_67_US.zip HEM367]
 == Inclusion  ==

@@ Line 5: / Line 5: @@
 There have been reported issues with HEM firmware less than 3.61. If you don't have 3.61, download this file [http://wiki.micasaverde.com/images/0/0c/HEM361.zip HEM361]
-=== Inclusion: When including the HEM to the Vera unit you should have the HEM&nbsp;powered with the <span style="color: rgb(255, 0, 0);">USB AC adapter</span>.  ===
+== Inclusion  ==
-=== Note: You need to have it plugged in through the <span style="color: rgb(255, 0, 0);">USB AC adapter</span> for it to report the KWH accurately, because when it is battery operated it sleeps most of the time and it cannot accurately track KWH.&nbsp;  ===
+When including the HEM to the Vera unit you should have the HEM&nbsp;powered with the <span style="color: rgb(255, 0, 0);">USB AC adapter</span>.
 [[Category:User_Instructions]] [[Category:Hardware]]