View source for Supported Hardware

This is a page for Supported Z-Wave devices. 

Alternative hardware pages exist for 

*[[ZWave Add Controller|Z-Wave Handheld Remote Controls, Gateways and Scene Controllers]] 
*[[IP Cameras|IP Enabled Cameras]] 
*[[Insteon Supported Hardware|Insteon/X10 devices]] 
*USB, or USB-Serial, [[Serial Supported Hardware|Interface devices]]

In general, any device with the Z-Wave logo should work with Vera. A list of tested Z-Wave devices is below, with specific notes for each type of device. This is a wiki, so feel free to add to the page. To learn about Z-Wave routing and fixing routing problems see: [[Heal Network]] 

== Hardware Reported to Work  ==

*We strongly encourage users to list any and all products they tested and installed. 
*If a product works but you did not like it, please list it anyway. It may be the only product available to some users.

<br> 

----

'''IMPORTANT! The devices listed here have been added by installers, technicians and users like yourself. Results may vary upon installations. MiCasaVerde does not guarantee operation and compatibility with your installation. The listed devices were found to work with their specific installation. Mixing different series and brands of equipment is not guaranteed in any way to work with other series and brands. It is very likely that users have not fully tested all features of the devices, so it is possible that a device listed here as compatible, will not prove compatible with your hardware. If you are editing this wiki DO NOT REMOVE a listed working device if it hasn't worked for you. Seek help to get the device to work under your individual circumstance. If you are adding to this wiki, please provide links to data for the device and add any tips you feel may benefit someone wanting to implement the device into an installation.''' 

----

<br> 

=== '''Lighting Devices'''  ===

{| cellpadding="2" border="1" style="width: 1220px; height: 491px;"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added by User 
! Notes
|-
| ACT 
| 2-way Dimmer Switch 
| ZDW120 
| <br> 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/ZDW120---Z-Wave-600-Watt-2-Wire-Dimmer-ACT-HomePro-P17C64.aspx Link] 
| [http://store.homeseer.com/store/ZDW120---Z-Wave-600-Watt-2-Wire-Dimmer-ACT-HomePro-P17C64.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=49 WSeverino] 
| Works well, easy to install, LED is a very bright blue....can be programmed to be off when the light is off or on.
|-
| ACT 
| 3-way Dimmer Switch 
| ZDW103 
| <br> 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/ZDW103---Z-Wave-500-Watt-3-way-Dimmer-ACT-HomePro-P19C64.aspx Link] 
| [http://store.homeseer.com/store/ZDW103---Z-Wave-500-Watt-3-way-Dimmer-ACT-HomePro-P19C64.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=49 WSeverino] 
| Works well, can be tricky to install due to the different combination of 3 way circuits, LED is a very bright blue....can be programmed to be off when the light is off or on.
|-
| ACT 
| 2-wire Dimmer Switch 
| ZDW232 
| <br> 
| Jul 2010 
| Indoor 
| [http://www.zwave4u.com/products/en/Switches-and-Dimmers/HomePro-Single-Wall-Dimmer-2-wire.html Link] 
| [http://www.zwave4u.com/products/en/Switches-and-Dimmers/HomePro-Single-Wall-Dimmer-2-wire.html Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=5198 Newb] 
| Wall-mount, 230v, 500W, 2-Wire (no neutral), works well. Can be programmed to be off when the light is off or on.
|-
| ACT 
| 2-way Relay Switch 
| ZRW113 
| <br> 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/ZRW113---Z-Wave-20-Amp-3-way-ISO-Relay-ACT-HomePro-P491C63.aspx Link] 
| [http://store.homeseer.com/store/ZRW113---Z-Wave-20-Amp-3-way-ISO-Relay-ACT-HomePro-P491C63.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=49 WSeverino] 
| Controls Florescent Lamps very well! No humming at all.
|-
| ACT 
| Companion Switch 
| AS101 
| <br> 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/AS101---Z-Wave-3-Way-Companion-Switch-ACT-HomePro-P10C63.aspx Link] 
| [http://store.homeseer.com/store/AS101---Z-Wave-3-Way-Companion-Switch-ACT-HomePro-P10C63.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=49 WSeverino] 
| Works well, can be tricky to install due to the different combination of 3 way circuits, The trick here is to install this device where the power comes in.
|-
| ACT<br> 
| 3-way Dimmer Switch, 2 rocker<br> 
| ZDM230<br> 
| 1.1<br> 
| Aug 2009<br> 
| Indoor<br> 
| [http://www.act-solutions.com/HomePro/pdfs/HomePro/Specs/ZDM230_spec.pdf Link]<br> 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=3015 TedStriker]<br> 
| Dimmer, Wall-mount, 230v, 500W,<br>3-way, 3 Wire, 2 rocker<br>
|-
| ACT 
| 3-way Relay Switch, 2 rocker 
| ZRM230<br> 
| 1.1<br> 
| Aug 2009<br> 
| Indoor<br> 
| [http://www.act-solutions.com/HomePro/pdfs/HomePro/Specs/ZRM230_spec.pdf Link]<br> 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=3015 TedStriker]<br> 
| <font size="2">Relay, Wall-mount, 230v, 6A,<br> 3-way, 3 Wire, 2 rocker - '''Status polling does not work with Vera'''<br></font>
|-
| Cooper 
| Accessory (3-way slave) 
| <br> 
| <br> 
| <br> 
| Indoor 
| <br> 
| <br> 
| <br> 
| See [[Cooper Accessory Slave]]
|-
| Düwi 
| 2 wire dimmer 
| <br> 
| <br> 
| July 2011 
| Indoor 
| <br> 
| <br> 
| intveltr 
| In-wall dimmer.
|-
| Düwi 
| 3 wire switch 
| 05431 
| <br> 
| July 2011 
| Indoor 
| <br> 
| <br> 
| intveltr 
| In-wall switch.
|-
| Düwi 
| 3 wire switch 
| 06431 
| <br> 
| July 2011 
| Indoor 
| <br> 
| <br> 
| intveltr 
| The newer in-wall Düwi switch (also designated Düwi.me), marked with a green sticker on the housing. This switch supports status push.
|-
| Fibar 
| 3 wire double switch 
| FGS221 
| <br> 
| Oct 2011 
| Indoor 
| <br> 
| <br> 
| intveltr 
| This device is designed to use (and be mounted behind) existing light switches. Supports status push. Also available: single switch, dimmer, blind control.
|-
| GE/Jasco 
| 2-wire Dimmer 
| 45606 
| &nbsp; 
| 2/2011 
| Indoor 
| [http://www.jascoproducts.com/support/manual-downloads/applications/DocumentLibraryManager/upload/45606-Manual-Eng.pdf Link] [http://www.jascoproducts.com/products/pc/GE-Z-Wave-Wireless-Lighting-Control-Dimmer-Switch-63p555.htm Link] 
| &nbsp; 
| [http://forum.micasaverde.com/index.php?action=profile;u=64 Anthonyris] 
| Works fine with most bulbs. With Philips AmbientLED, flickers at &gt;95% brightness. Supports beaming.
|-
| Innovus 
| Relay Switch Adapter 
| RAone SmartPower 
| &nbsp; 
| Aug 2009 
| Indoor 
| [http://www.innovus.eu/fileadmin/user_upload/manual/z-wave/smartpower_zw_tech_doc.pdf Link] 
| &nbsp; 
| [http://forum.micasaverde.com/index.php?action=profile;u=3015 TedStriker] 
| Works very well + it has a build in powermeter which works perfect with Vera
|-
| Innovus 
| Dimmer Switch Adapter 
| RAone SmartDimmer 
| &nbsp; 
| Aug 2009 
| Indoor 
| [http://www.innovus.eu/fileadmin/user_upload/manual/z-wave/smartdimmer-00110001-tech.pdf Link] 
| &nbsp; 
| [http://forum.micasaverde.com/index.php?action=profile;u=3015 TedStriker] 
| Works very well + it has a build in powermeter which works perfect with Vera
|-
| Intermatic 
| Lamp Module 
| HA03C 
| &nbsp; 
| Sept 2010 
| Indoor 
| [http://www.homesettings.com/products/modules/ha03.aspx Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=5852 JonnyO] 
| Easy to Instal, supports dimming
|-
| Intermatic 
| Screw-in Lamp Module 
| HA05C 
| <br> 
| Nov 2008 
| Indoor/Outdoor 
| [http://store.homeseer.com/store/HA05C---Z-Wave-IndoorOutdoor-Screw-in-Module-Intermatic-HomeSettings-P1C62.aspx Link] 
| [http://store.homeseer.com/store/HA05C---Z-Wave-IndoorOutdoor-Screw-in-Module-Intermatic-HomeSettings-P1C62.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=49 WSeverino] 
| Easy install, easy to pair with Vera!
|-
| Intermatic 
| 300 watt dimmer 
| HA06 
| <br> 
| July 2007 
| Indoor 
| [http://www.homesettings.com/products/modules/ha06.aspx Link] 
| <br> 
| <br> 
| Affordable Dimmer Switch. incandescent/halogen only. Loads for 300 watts or less no neutral required. Great for dimming one bulb.
|-
| Intermatic 
| 3-way Switch 
| HA18 
| <br> 
| Dec 2008 
| Indoor 
| [http://www.homesettings.com/products/new%20products/ha18.aspx Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=66 Kozanator] 
| Affordable 3-way Switch
|-
| Intermatic 
| 3-way Dimmer Switch 
| HA20 
| <br> 
| Nov 2008 
| Indoor 
| [http://www.homesettings.com/products/new%20products/ha20.aspx Link] 
| [http://www.smarthome-products.com/p-460-intermatic-homesettings-ha20c-3-way-in-wall-switch-dimmer.aspx Link] 
| <br> 
| Affordable 3-way 600W dimmer
|-
| Leviton 
| Dimmer Switch 
| VRI06-1LX 
| &nbsp; 
| Aug 2009 
| Indoor 
| [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=305784&section=25501 Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=2618 guessed] 
| Works well
|-
| Leviton 
| 4-Scene Controller with Switch 
| VRCS4-MRX 
| 7,2,67,0,2 
| Aug 2009 
| Indoor 
| [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=433270&section=28563 Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=2618 guessed] 
| Works well, pair as per [http://wiki.micasaverde.com/index.php/Leviton_Scene_Controller Leviton 4-Scene Controller], then again holding "2" and "4" to pair the Switch ("Load") itself.
|-
| Leviton 
| Dimmer Switch 
| VRM10-1LX 
| 1 
| Nov 2008 
| Indoor 
| [http://shop.micasaverde.com/index.php?main_page=product_info&cPath=104&products_id=170 Link] 
| [http://www.amazon.com/review/product/B000ZKM7I8/ref=dp_top_cm_cr_acr_txt?_encoding=UTF8&showViewpoints=1 Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=65 mark-hc] 
| This is a high quality dimmer geared towards high-end installations
|-
| Leviton 
| Scene capable 3-way switch (non-dimming)
| VRS15-1L 
| &nbsp; 
| May 2011 
| Indoor 
| [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=305791&section=25502&minisite=10026 Link] 
| <br> 
| DaveL17 
| (Coordinating Remote??)
|-
| Leviton 
| Scene capable 3-way switch (non-dimming)
| VRS15-1LX 
| &nbsp; 
| Oct 2011 
| Indoor 
| [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=305791&section=25502&minisite=10026 Link] 
| <br> 
| DaveL17 
| Works well. Pair normally. Can also be used in single pole applications. [Note: white, ivory, [[almond]].]
|-
| Leviton 
| Scene capable 3-way switch (non-dimming)
| VRS15-1LZ 
| &nbsp; 
| &nbsp; 
| Indoor 
| [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=305791&section=25502&minisite=10026 Link] 
| <br> 
| DaveL17 
| Works well. Pair normally. Can also be used in single pole applications. [Note: white, ivory, [[light almond]].]
|-
| Merten 
| Radio sensor cover for dimmer inserts 
| 5026xx, 5036xx, 5046xx 
| 6,2,7,1,5 
| Apr 2009 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5026_581_01_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well
|-
| Merten 
| Radio sensor cover for switch inserts 
| 5024xx, 5034xx, 5044xx 
| 6,2,27,2,2 
| &nbsp; 
| Indoor 
| [http://www.merten.de/download/DL_doku/5024xx_5034xx_5044xx_Sensorflaeche4pin_CONNECT_INT.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well
|-
| Merten 
| Single Radio flush-mounted receiver 
| 507001 
| 6,2,27,2,2 
| Apr 2009 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5070_581_01_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well
|-
| Merten 
| switch, flush-mounted 
| 507501, 507601 
| &nbsp; 
| &nbsp; 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5075_581_00_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well (according to [http://forum.micasaverde.com/index.php?topic=276.15 Link])
|-
| Merten 
| 1-gang universal dimmer, flush-mounted 
| 507900 
| &nbsp; 
| &nbsp; 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5079_581_01_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well (according to [http://forum.micasaverde.com/index.php?topic=276.15 Link])
|-
| Schlage 
| Lamp Module 
| RP200 
| 1.0 
| Aug 2009 
| Indoor 
| [http://consumer.schlage.com/products/Productdetail3.asp?StyleID=139&FinishID=12&FunctionID=77 Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=2870 LibraSun] 
| Works well<br>Sold with Schlage LiNK lock system
|}

<br> 

=== '''Plug &amp; Receptacle Devices'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Frequency 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added by User 
! Notes
|-
| ACT 
| In-Wall Receptacle 
| ZRR150W 
| 2.2 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://www.smarthome-products.com/p-527-homepro-zrr150-wall-receptacle.aspx Link] 
| [http://www.smarthome-products.com/p-527-homepro-zrr150-wall-receptacle.aspx Link] 
| <br> 
| Works like a champ! Easy to Install. One receptacle RF controlled, the other is hot
|-
| ACT 
| In-Wall Receptacle 
| ZRP200 
| &nbsp; 
| EU 
| July 2011 
| Indoor 
| &nbsp; 
| &nbsp; 
| intveltr 
| Basic plug-in switch.
|-
| ACT 
| In-Wall Receptacle 
| ZDP200 
| &nbsp; 
| EU 
| July 2011 
| Indoor 
| &nbsp; 
| &nbsp; 
| intveltr 
| Basic plug-in dimmer.
|-
| Cooper Wiring Devices 
| In-Wall Receptacle 
| RFTR9505-T 
| &nbsp; 
| &nbsp; 
| &nbsp; 
| Indoor 
| [http://solutions.cooperwiringdevices.com/common/brands.cfm?pg=Detail&brandName=CWD%20Technology&category=Aspire%20RF%20Lighting%20Control%20System%3A%20Receptacles&id=16772 Link] 
| <br> 
| <br> 
| One receptacle is RF controlled, the other is hot
|-
| Duwi 
| <span class="S33">Z-Wave switch 3500 W</span> 
| <span class="S31">05437</span> 
| &nbsp; 
| EU 
| Feb 2009 
| Indoor 
| [http://www.duewi.com/ Link] 
| <br> 
| ezhome 
| High quality Plug-in switch, Easy install and works well
|-
| Everspring 
| <span class="S33">Z-Wave switch 3500 W</span> 
| <span class="S31">AN157-2</span> 
| 4,2,64,1,2 
| EU 
| &nbsp; 
| Indoor 
| [http://www.everspring.com/Products/Home_Automation_Detail.asp?parentUID=83&UID=501&CateUIDList=0,83 Link] 
| <br> 
| Ap15e 
| Works well.
|-
| Everspring 
| <span class="S33">Z-Wave switch 3500 W</span> 
| <span class="S31">AN158</span> 
| &nbsp; 
| EU 
| &nbsp; 
| Indoor 
| &nbsp; 
| <br> 
| intveltr 
| Works well. Supports status push and power metering
|-
| GE/Jasco 
| In-wall Duplex Receptacle 
| 45605 
| &nbsp; 
| US 
| 2/2011 
| Indoor 
| [http://www.jascoproducts.com/products/pc/GE-Z-Wave-Wireless-Lighting-Control-Duplex-Receptacle-63p554.htm Link] [http://www.jascoproducts.com/support/manual-downloads/applications/DocumentLibraryManager/upload/45605-Manual-Eng.pdf Link] 
| &nbsp; 
| [http://forum.micasaverde.com/index.php?action=profile;u=64 Anthonyris] 
| Easy. Works.
|-
| Home Manageables 
| Lamp Module (Dimming) 
| HM-LM001 
| &nbsp; 
| &nbsp; 
| Nov 2011 
| Indoor 
| 200W maximum load, 25W minimum load 
| [http://www.homemanageables.com/manuals/HM-LM001%20Manual%20Final.pdf Link] 
| DaveL17 
| Works well. Support for incandescent loads only. Not load sensing.
|-
| Intermatic 
| In-Wall Receptacle 
| CA3500 
| 1 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://shop.micasaverde.com/index.php?main_page=product_info&cPath=105&products_id=97 Link] 
| [http://www.amazon.com/review/product/B000U3XYPA/ref=dp_top_cm_cr_acr_txt?_encoding=UTF8&showViewpoints=1 Link] 
| <br> 
| This is a decent, but expensive solution for in-wall receptacles. One receptacle RF controlled, the other is hot.
|-
| Intermatic 
| Appliance Module 
| HA02C 
| 1 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://shop.micasaverde.com/index.php?main_page=product_info&cPath=108&products_id=98 Link] 
| [http://www.amazon.com/Intermatic-HA02C-Settings-Heavy-Duty-Appliance/dp/B000BJSDZO/ref=sr_1_3?ie=UTF8&qid=1227467418&sr=8-3 Link] 
| <br> 
| Seems to work well
|-
| Intermatic 
| Outdoor Module 
| HA04C 
| 1 
| &nbsp; 
| Dec 2008 
| Outdoor 
| [http://store.homeseer.com/store/HA04C---Z-Wave-Outdoor-Module-Intermatic-HomeSettings-P6C62.aspx Link] 
| [http://store.homeseer.com/store/HA04C---Z-Wave-Outdoor-Module-Intermatic-HomeSettings-P6C62.aspx Link] 
| [http://forum.micasaverde.com/index.php?action=profile;u=66 Kozanator] 
| Easy to Install.
|-
| Merten 
| switch, plug adapter, 2000 W 
| 508519 
| 6,2,7,1,5 
| EU 
| &nbsp; 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5085_581_01_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well.
|-
| Monster Central 
| 1800W Appliance Module 
| ML-LAS1000 
| 1 
| &nbsp; 
| Jan 2009 
| Indoor 
| [http://www.monstercable.com/productdisplay.asp?pin=3164 Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=2618 guessed] 
| Easy to Install. I use this as a ZWave signal repeater. Appears to be a badge-engineering of [http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=309748&section=25542 Leviton VRP15-1LW]
|-
| Wayne Dalton 
| Lamp Module 
| HA-03WD 
| 
| 
| Dec 2011 
| Indoor 
| [http://www.waynedaltonstore.com/ssi/pdf/wayne/HA-03WD.pdf Link] 
| 
| DaveL17 
| Not load sensing.
|}

<br>

=== '''Thermostat Devices'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Frequency 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added<br>By User 
! Notes
|-
| Wayne Dalton 
| Wall Stat 
| WDTC-20 
| &nbsp;?? 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/WDTC-20---Z-Wave-Thermostat-Wayne-Dalton-P599C38.aspx Link] 
| [http://www.amazon.com/Wayne-Dalton-Corporation-Z-Wave-Thermostat/dp/B001F8QKYQ Link] 
| <br> 
| Has 2 inclusion modes: 1) press and release the bind button and the STAT will be included as a thermostat and works with Vera, 2) press and hold the bind button and it will be added as a binary switch for compatibility with old, non-compliant remotes. If it's added in the wrong mode, remove it and re-add it. Works great simple to use!
|-
| HAI 
| Wall Stat 
| RC-80BZ 
| &nbsp;?? 
| &nbsp; 
| Nov 2007 
| Indoor 
| [http://www.homeauto.com Link] 
| [http://www.homeauto.com/Downloads/Products/Omnistat/rcr80.pdf Link] 
| <br> 
| Shows up as Standard Thermostat in Vera, Hold button feature not able to control by Vera at this time. Priced above 200.00. Has internal setback programs. Works great.
|-
| RCS 
| Wall Stat 
| TZ43 
| &nbsp;?? 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://store.homeseer.com/store/TZ43---Z-Wave-Thermostat-RCS-P627C67.aspx Link] 
| [http://store.homeseer.com/store/TZ43---Z-Wave-Thermostat-RCS-P627C67.aspx Link] 
| <br> 
| Shows up as Standard Thermostat in Vera, much more feature rich the the WDTC-20 but comes with a hefty price tag ($214.95). Wish Vera could use all the features in this Thermostat! '''Note:'''''You need to set the thermostat to show the temperature, on its display, in Celsius degree in order to be able to receive "Set Temp" commands from Vera. This is no longer required in firmwares above '''''<i>1.0.862 (luup)</i>'''
|-
| Schlage/Trane 
| Wall Stat 
| Trane 
| &nbsp;?? 
| &nbsp; 
| &nbsp;?? 
| Indoor 
| [http://www.link.schlage.com/Products/Pages/Thermostat.aspx Link] 
| [http://www.trane.com/Residential/Products/Thermostats Link] 
| <br> 
| It's the same thermostat as the RCS TZ43 and it has the same issue: it's accepting "Set Temp Point" commands only in the measurement unit that is displayed on its screen. '''Note:'''''You need to set the thermostat to show the temperature, on its screen, in Celsius degree in order to be able to receive "Set Temp" commands from Vera. This is no longer required in firmwares above '''''<i>1.0.862 (luup)</i>'''
|-
| Intermatic 
| InTouch 
| CA8900 
| <br> 
| &nbsp; 
| Nov 2008 
| Indoor 
| [http://www.smarthome-products.com/p-663-intermatic-intouch-ca8900-z-wave-digital-thermostat.aspx Link] 
| <br> 
| <br> 
| Looks very similar to the Wayne Dalton WDTC-20 listed here. works great, simple to use
|-
| Danfoss 
| Radiator thermostat 
| RA PLUS-w 
| <br> 
| EU 
| <br> 
| Indoor 
| [http://raplusw.com/Content/E962FC0B-6461-4319-82FE-3E1E765142CF.html Link] [http://raplusw.com/PCMPDF/Data%20sheet%20RA-PLUS-w_02.pdf Link] 
| [http://www.eurox10.com/Product/ZWave/Actuators/ZWDNF_RA_PLUS-W.htm Link] [http://www.eurox10.com] 
| <br> 
| See: [[Danfoss Thermostat]] for installation instructions<br>If the device cannot be configured at the final location, move the device closer to Vera and try again (this device might require a direct connection to Vera for configuration).
|-
| Radio Thermostat 
| Wall Stat 
| CT22 
| <br> 
| US 
| <br> 
| Indoor 
| [http://www.radiothermostat.com/documents/CT-22-Operation-27aug10.pdf Link] [http://www.radiothermostat.com/documents/CT-22-Installation-27aug10.pdf Link] 
| <br> 
| Daniel 
| To include the thermostat into your network, you just have to install the USNAP module in the thermostat while Vera is in Include mode. You can watch a video about how to install it [http://www.youtube.com/watch?v=M9VNuHGENP0 here]
|-
| Horstmann 
| Wall Stat 
| HRT4-ZW 
| 
| EU 
| 
| Indoor 
| [http://horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4-ZWweb.pdf Link] [http://horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4B-ZWManual.pdf Link] 
| [http://horstmann.co.uk/downloads/ElectronicDocuments/Central-Heating/HRT4B-ZWManual.pdf <br>] 
| Daniel 
| After you include the thermostat in Vera's network, you will have to make some configuration changes in order for it to report the temperature change. See: [[HRT4-ZW]] for more information.
|}

<br> 

=== '''Sensors'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Frequency 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added by User 
! Notes
|-
| ACT 
| Motion Sensor 
| ZIR000 / ZIR010 
| <br> 
| EU (ZIR010) or US (ZIR000) 
| <br> 
| Indoor 
| [http://www.act-solutions.com/HomePro/pdfs/HomePro/Specs/ZIR000_spec.pdf Link] [http://www.act-solutions.com/HomePro/pdfs/HomePro/Inst/ZIR000_instr.pdf Link] [http://www.act-solutions.com/HomePro/pdfs/HomePro/Specs/ZIR010_spec.pdf Link] [http://www.act-solutions.com/HomePro/pdfs/HomePro/Inst/ZIR010_instr.pdf Link] 
| <br> 
| <br> 
| Remove the cover, pair to Vera's dongle by using the push-button on the left of the circuit board. Vera must configure it to work, and it can only be configured within less of a minute (30 sec best) of inserting the batteries. With Vera's dongle removed, remove/reinsert the batteries, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page
|-
| Aeon Labs 
| 3-in-1 sensor (light/humidity/temperature) 
| MultiSensor 
| <br> 
| EU or US 
| <br> 
| Indoor/Outdoor 
| [http://www.aeon-labs.com/site/public/lib/download.php?type=s&f=29 Specs] 
| <br> 
| <br> 
| Pair to Vera by using the push-button. Vera must configure it to work, and it can only be configured within 10 minutes of inserting the batteries.
|-
| Express Controls aka HomeSeer 
| 3-in-1 sensor (light/temperature/motion) 
| HSM100 / EZMotion 
| <br> 
| EU or US 
| <br> 
| <br> 
| [http://www.expresscontrols.com/pdf/EZMotionOwnerManual.pdf Link] 
| <br> 
| <br> 
| See [[ExpressControls3in1]]<br>If the motion sensor does not work right after inclusion and configuration, remove the batteries for a few seconds.
|-
| EverSpring/Hawking/Home Manageables 
| Door/window sensor 
| SM103 
| 6,2,9,1,0 
| EU or US 
| Apr 2009 
| Indoor 
| [http://www.everspring.com/Products/Home_Automation_Detail.asp?parentUID=83&UID=355&CateUIDList=0,83 Link] [http://www.everspring.com/Archive/Image/File/A501110873R01_SM103_-ECR.pdf Link] 
| &nbsp; 
| Ap15e 
| Pair using the intrusion button. The sensor will accept configuration within a few minutes of the initial pairing, or of pressing the intrusion button on the back even after it's paired. Pair the device, or if it's already paired, press the intrusion button, and within 30 seconds insert Vera's dongle. Within a few minutes confirm the "configure" icon for the device is green on Vera's setup page. NOTE: There is some confusion about the orientation of the sensor. The main sensor body has a back (where the intrusion is), a front (where the logo and LED is), and the 2 other surfaces, one of which has a curved edge, and the other is flat. The magnet needs to go against the flat surface. And the flat surface on the magnet should be as close as possible to the flat surface on the sensor, lined up in the middle so the line which passes through the LED lines up with the sensor. 
Note: In case the inclusion/exclusion fails you should remove/reinsert the batteries from the sensor and within a few seconds the sensor should be automatically detected. 

|-
| EverSpring/Home Manageables 
| Humidity + Temperature sensor 
| HM-TS001 
| <br> 
| <br> 
| Jan 2010 (requires version 1.1.0 or greater) 
| Indoor 
| [http://www.asihome.com/ASIshop/product_info.php?products_id=3946 Link] [http://www.homeseer.com/pdfs/guides/HM_TD001.pdf Link] 
| &nbsp; 
| micasaverde 
| Pair or unpair the device by tapping the CF button 3 times very quickly. Once it's paired and shows up in the UI as a generic device, press the CF button 3 times again quickly to make it wakeup and get configured. Then it will correctly be identified as 3 devices (combo device + temperature + humidity).
|-
| Everspring 
| Motion Detector 
| SP103 
| 6,2,9,1,0 
| EU or US 
| Apr 2009 
| Indoor 
| [http://www.everspring.com/Products/Home_Automation_Detail.asp?parentUID=83&UID=354&CateUIDList=0,83 Link] [http://www.everspring.com/Archive/Image/File/A501110874R01_SP103_%20-%20ECR.pdf Link] 
| &nbsp; 
| Ap15e 
| Works well
|-
| Fortrezz 
| Water /Freeze 
| WWA-001 
| &nbsp;?????? 
| US 
| Apr 2009 
| Indoor 
| [http://www.Fortrezz.com Link] [http://www.fortrezz.com/resources/WWA_manual_01May2009.pdf Link] 
| <br> 
| Zmistro 
| Works great I would place a few in your house. Bathrooms, laundry , kitchen , basement. Great product!
|-
| Intermatic 
| Motion Sensor 
| CA-9000 
| <br> 
| US 
| <br> 
| Indoor 
| <br> 
| <br> 
| Aaron 
| This device has limited functionality as a sensor. It can only be used to turn on and off a light directly by setting an association, which Vera supports. It does not fire events, so you cannot use it as an event on a scene.
|-
| Merten 
| 4-gang radio transmitter, flush-mounted 
| 506004 
| 2,2,27,1,4 
| EU 
| &nbsp; 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5060_581_02_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Note: There is proprietary functionality here. Support will be added soon. 
Quite complex device; partially supported by Vera; can be used as a window/door sensor (as of firmware 1.0.900) ... 

|}

<br> 

=== '''Door Locks'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added<br>By User 
! Notes
|-
| Schlage 
| Door lock and deadbolt 
| BE369 (deadbolt) 
| <br> 
| Mid 2009 
| Indoor 
| [http://consumer.schlage.com/link/product_tour/ Link] 
| <br> 
| [http://forum.micasaverde.com/index.php?action=profile;u=2870 LibraSun] 
| Read the instructions here: [[Schlage Lock]]
|-
| Kwikset 
| Door lock and deadbolt 
| 
| 
| 
| Indoor 
| 
| 
| 
| Read instructions here:[[Kwikset Lock]]
|-
| Yale 
| Deadbolt 
| Real Living 
| 
| 
| Indoor 
| 
[http://www.yaleresidential.com/Yale/Yale%20US/Real%20Living/Documents%20Library/Yale%20DB%20PUSH%20Quickstart%2018JUL11_Rev%20B.pdf Link] 

[http://www.yaleresidential.com/Yale/Yale%20US/Real%20Living/Documents%20Library/Yale%20DB%20PUSH%20Instructions%2023AUG11_Rev%20B.pdf Link] 

| 
| 
| Read instructions here: [[Yale Lock]]
|}

<br>

=== '''Drapes/Blinds'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added<br>By User 
! Notes
|-
| Electronic Solutions 
| Drape/Blind Motor Controller 
| DBMZ 
| V2+1 
| <br> 
| Indoor 
| For 12-24VDC Motors 
| [http://www.elec-solutions.com/products/dc_mot_ctrls/z-wave/dbmz/dbmz.html Link] 
| Shady 
| 2-Wire Motors
|-
| Electronic Solutions 
| Drape/Blind Motor Controller 
| ABMHZ 
| V2+1 
| <br> 
| Indoor 
| For 110-230VAC Motors 
| [http://www.elec-solutions.com/products/int_ac_mot_ctrls/z-wave/abmhz/abmhz.html Link] 
| Shady 
| 4-Wire Motors
|-
| Lagotek / RSSceneAutomation 
| Drape/Blind Motor Controller 
| DC1-ZW 
| <br> 
| <br> 
| Indoor 
| For 12-24VDC Motors 
| [http://www.lagotek.com/blindspdf/AC1-ZW%20Cut%20Sheet.pdf Link] 
| Shady 
| 2-Wire Motors
|-
| Lagotek / RSSceneAutomation 
| Drape/Blind Motor Controller 
| AC1-ZW 
| <br> 
| <br> 
| Indoor 
| For 110-230VAC Motors 
| [http://www.lagotek.com/blindspdf/DC1-ZW%20Cut%20Sheet.pdf Link] 
| Shady 
| 4-Wire Motors
|}

<br> 

=== '''Relay controls'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added<br>By User 
! Notes
|-
| Intermatic 
| Contactor control box 
| CA3750 
| <br> 
| Nov 2007 
| Indoor/Outdoor 
| [http://www.intouchcontrols.com/~/media/Files/InTouchControls/Products/Spec%20Sheets/CA3750.ashx Link] 
| <br> 
| <br> 
| Multi-instance class supported for this device. Vera is able to control each of the 2 relays independently if desired. please note unit shows as three switches this is a bug with Intermatic not a real issue.You can check the box in devices to not show the second listing of the first relay in "Dasboard" You can control heavy loads like a water heater ,pool pump motor/s. great device
|}

<br> 

=== '''Window Coverings'''  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Frequency 
! Date Purchased 
! Location (indoor/outdoor) 
! Specs 
! Product Review 
! Added by User 
! Notes
|-
| Merten 
| Radio roller shutter push-button 
| 5025xx, 5035xx, 5045xx 
| 6,2,27,2,3 and 6,2,27,2,4 
| EU 
| Apr 2009 
| Indoor 
| [http://www.merten.de/download/DL_doku/V5025_581_01_web.pdf Link] 
| &nbsp; 
| Ap15e 
| Open/Close buttons work well, but slide bar does not work. GUI buttons do not work with Luup release 1.0.843 and 1.0.862 (fixed with Luup release 1.0.879).<br>Workaround: Use a Luup Scene with the following code:<tt></tt> 
<tt>local lul_arguments = {}</tt> 

<tt>lul_arguments["newTargetValue"]="0"</tt> 

<tt>lul_resultcode,lul_resultstring,lul_job,lul_returnarguments = luup.call_action("urn:upnp-org:serviceId:SwitchPower1","SetTarget",lul_arguments,6) </tt> Replace "6" with your device number, replace "0" with "1" for inverse action. 

|-
| Duewi 
| Radio roller shutter push-button 
| 054368 
| 6,2,51,1,0 
| EU 
| Jun 2009 
| Indoor 
| [http://www.duewi.de/index.php?productid=37344 Link] 
| &nbsp; 
| Lutz 
| Open/Close buttons work well, but slide bar does not work.<br><br>Some additional observations by Ap15e (Vera V1, firmware 1.0.979): 
*GUI button 'Stop' and corresponding UPnP service does not work. 
*GUI button 'Up' moves the shutter down, GUI button 'Down' moves the shutter up ... 
*After adjusting the running times even the slide bar seems to work! 
*I got a report from a user that the düwi device may fail due to interference from the shutter motor. In this case an additional filter is required (costs about 25 €/direction). 
*More information is available at [http://forum.micasaverde.com/index.php?topic=3359.msg16142#msg16142 Link]

|}

<br> 

=== '''Cameras that work'''  ===

See [http://wiki.micasaverde.com/index.php/IP_Cameras IP Cameras] for a more comprehensive and up to date list 

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Device Type 
! Model no. 
! Version 
! Date Purchased 
! Location (indoor/outdoor) 
! Path for JPEG image 
! Product Review 
! Notes
|-
| Linksys 
| IP Camera 
| WVC54GCA 
| all 
| 2009 
| Indoor 
| img/snapshot.cgi 
| <br> 
| An inexpensive camera with moderate image quality. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address.
|-
| Linksys 
| IP Camera 
| WVC210 
| all 
| 2009 
| Indoor 
| img/snapshot.cgi 
| <br> 
| A more expensive camera with good image quality and pan/tilt ability. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address. Pan/tilt controls will not work with Vera.
|-
| Linksys 
| IP Camera 
| WVC80N 
| all 
| 2009 
| Indoor 
| img/snapshot.cgi?size=2&amp;quality=1 
| <br> 
| A more expensive camera with good image quality and wireless N. Use the Linksys setup wizard for initial setup, then copy IP address and path into Vera setup fields. Use a static IP address. Pan/tilt controls will not work with Vera. 
Size can be (160 x 120 = 1,320 x 240 = 2,640 x 480 = 3) and Quality can be (Very High= 1,High= 2,Normal= 3,Low= 4,Very Low= 5) 

|-
| iCamView 
| IP Camera Server 
| iCV-22, iCV-32 
| all 
| 2009<br> 
| Indoor/Outdoor 
| pda.cgi?user=admin&amp;password=1234&amp;page=image&amp;cam=1<br><br>pda.cgi?user=admin&amp;password=1234&amp;page=image&amp;cam=2<br> 
| <br> 
| Feature-rich IP camera server, suports up to two compatible USB cameras, optional WiFi support, USB storage, USB hubs, motion; works with range of cameras, see icamview.co.uk. Excellent modular solution. They do ship to North America.
|-
| SmartHome.com.au 
| IP Camera 
| Z~Series Wireless Camera 
| all 
| 2009<br> 
| Indoor 
| tmpfs/auto.jpg 
| <br> 
| Inexpensive IP security camera designed for the Australian and New Zealand Z-Wave users, but shipping world wide.
|-
| [http://global.level1.com LevelOne] 
| IP Camera 
| WCS-2030 
| all 
| 2010 
| Indoor 
| cgi-bin/video.jpg 
| [http://reviews.cnet.com/search-results/levelone-camcon-wcs-2030/1707-5_7-31972011.html CNET review] 
| An inexpensive IP camera with good image quality. Can be connected wired or wirelessly. Most LevelOne cameras use the same path for the JPEG image, so most of their line (both low and high end) should be compatible. Video and audio also stream over RTSP, which can be customized through the camera's web interface.
|-
| Asante 
| IP Camera 
| Voyager I 
| firmware 2.02 and above 
| 2010 
| Indoor 
| image.cgi 
| <br> 
| An inexpensive&nbsp;IP&nbsp;camera that is very feature rich, has good image quality, night vision capabilities, motion detection, two-way audio, video streaming over TCP, UDP, or HTTP, and other configurable features. In firmware version 2.02, Asante added the capability to retrieve an image via a URL (however, it is delayed by 3 seconds). Offers a full-featured web interface in IE using an ActiveX plug-in (limited capabilites in other browsers).
|}

<br> 

=== Alarm Panels  ===

{| cellpadding="2" border="1"
|-
! Manufacturer 
! Model(s) 
! Required module 
! Plugin 
! Notes
|-
| DSC 
| 
*[http://www.dsc.com/index.php?n=products&o=view&id=1 PowerSeries PC1616] 
*[http://www.dsc.com/index.php?n=products&o=view&id=2 PowerSeries PC1832] 
*[http://www.dsc.com/index.php?n=products&o=view&id=3 PowerSeries PC1864]

| [http://www.dsc.com/index.php?n=products&o=view&id=22 IT-100] 
| [http://code.mios.com/trac/mios_dscalarmpanel/wiki/WikiStart Link] 
| 
|-
| Elk 
| 
*[http://www.elkproducts.com/_webapp_2981420/M1_Gold_Cross_Platform_Control%C2%AE M1 Gold] 
*[http://www.elkproducts.com/_webapp_3127911/M1EZ8_Cross_Platform_Control%C2%AE M1EZ8]

| The M1EZ8 panel requires the [http://www.elkproducts.com/_webapp_2981423/elk-m1ez8msi__m1ez8_main_serial_interface ELK-M1EZ8MSI] Main Serial Port Interface. 
| [http://code.mios.com/trac/mios_elk-alarm-panel/wiki/WikiStart Link] 
| You can use the ELK-M1XEP Ethernet Interface to connect the panels to Vera on the Ethernet port.
|-
| GE Security / Interlogix / Caddx 
| 
*[http://www.interlogix.com/resources/intrusion/906-3179_NetworX_brochure.pdf NetworX NX-4] 
*[http://www.interlogix.com/resources/intrusion/906-3179_NetworX_brochure.pdf NetworX NX-6] 
*[http://www.interlogix.com/resources/intrusion/906-3179_NetworX_brochure.pdf NetworX NX-8] 
*[http://www.interlogix.com/resources/intrusion/906-3179_NetworX_brochure.pdf NetworX NX-8E]

| [http://utcfssecurityproducts.com/ProductsAndServices/Pages/NX-584.aspx NX-584] 
| [http://code.mios.com/trac/mios_caddxnx584/wiki/WikiStart Link] 
| NetworX NX-8E already has a RS-232 interface, so it doesn't require the NX-584 module.
|-
| Honeywell / Ademco 
| VISTA-50P, VISTA-128BP, VISTA-128BPT, VISTA-128BPE, VISTA-128FBP, VISTA-250BP, VISTA-250BPT, VISTA-250BPE and VISTA-250FBP 
| VISTA-50P, VISTA-128BP, VISTA-128FBP, VISTA-250BP, and VISTA-250FBP panels require the [http://www.security.honeywell.com/me/intrusion/products/exp/ac/138478.html 4100SM] module. 
| [http://code.mios.com/trac/mios_ademco-panels-plugin/wiki/WikiStart Link] 
| If your Vista panel is not on this list, look at the next row.
|-
| Honeywell / Ademco 
| 10SE, 20SE, 10P, 15P, 20P, 50P, etc. 
| [http://www.nutech.com/online-store/18.html AD2USB] 
| [http://code.mios.com/trac/mios_vista-alarm-panel-ad2usb/wiki/WikiStart Link] 
| 
|-
| Paradox 
| 
*Digiplex DGP-848 
*EVO48 
*[http://www.paradox.com/Products/default.asp?CATID=7 EVO192]

| [http://www.paradox.com/Products/default.asp?CATID=7&SUBCATID=75&PRD=234 PRT3 Integration Module] 
| [http://code.mios.com/trac/mios_paradox-alarm/wiki/WikiStart Link] 
| 
|-
| Visonic 
| 
*[http://www.visonic.com/Products/Wireless-Property-Protection/PowerMax PowerMax] 
*[http://www.visonic.com/Products/Wireless-Property-Protection/PowerMaxPlus PowerMax+] 
*[http://www.visonic.com/Products/Wireless-Property-Protection/PowerMaxComplete PowerMaxComplete] 
*[http://www.visonic.com/Products/Wireless-Property-Protection/PowerMaxPro PowerMaxPro]

| RS-232 Interface Module 
| [http://code.mios.com/trac/mios_visonic-powermax/wiki/WikiStart Link] 
| 
|}

[[Category:User_Instructions]] [[Category:Hardware]]